- 您現在的位置：買賣IC網 > PDF目錄44986 > LT3724MPFE#TR (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, 225 kHz SWITCHING FREQ-MAX, PDSO16 PDF資料下載
參數資料
| 型號： | LT3724MPFE#TR |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, 225 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | 4.40 MM, PLASTIC, TSSOP-16 |
| 文件頁數： | 10/26頁 |
| 文件大?。?/td> | 309K |
| 代理商： | LT3724MPFE#TR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
LT3724
18
3724fd
APPLICATIONS INFORMATION
2. I2R losses are calculated from the DC resistances of the
MOSFET, the inductor, the sense resistor, and the input and
outputcapacitors.Incontinuousconductionmodetheaver-
age output current flows through the inductor and RSENSE
but is chopped between the MOSFET and the Schottky
diode. The resistances of the MOSFET (RDS(ON)) and the
RSENSE multiplied by the duty cycle can be summed with
the resistances of the inductor and RSENSE to obtain the
total series resistance of the circuit. The total conduction
power loss is proportional to this resistance and usually
accounts for between 2% to 5% loss in efficiency.
3. Transition losses of the MOSFET can be substantial with
input voltages greater than 20V. See MOSFET Selection
section.
4. The Schottky diode can be a major contributor of power
loss especially at high input to output voltage ratios (low
duty cycles) where the diode conducts for the majority
of the switch period. Lower Vf reduces the losses. Note
that oversizing the diode does not always help because
as the diode heats up the Vf is reduced and the diode loss
term is decreased.
I2R losses and the Schottky diode loss dominate at high
load currents. Other losses including CIN and COUT ESR
dissipative losses and inductor core losses generally ac-
count for less than 2% total additional loss in efficiency.
PCB Layout Checklist
When laying out the printed circuit board, the following
checklistshouldbeusedtoensureproperoperation.These
items are illustrated graphically in the layout diagram of
Figure 9.
1. Keep the signal and power grounds separate. The signal
ground consists of the LT3724 SGND pin, the exposed pad
on the backside of the LT3724 IC and the (–) terminal of
VOUT. The signal ground is the quiet ground and does not
containanyhigh,fastcurrents.Thepowergroundconsists
of the Schottky diode anode, the (–) terminal of the input
capacitor, and the ground return of the VCC capacitor. This
ground has very fast high currents and is considered the
noisy ground. The two grounds are connected to each
other only at the (–) terminal of VOUT.
2. Use short wide traces in the loop formed by the MOSFET,
the Schottky diode and the input capacitor to minimize
high frequency noise and voltage stress from parasitic
inductance. Surface mount components are preferred.
3. Connect the VFB pin directly to the feedback resistors
independent of any other nodes, such as the SENSE– pin.
Connect the feedback resistors between the (+) and (–)
terminals of COUT. Locate the feedback resistors in close
proximity to the LT3724 to keep the high impedance node,
VFB, as short as possible.
4. Route the SENSE– and SENSE+ traces together and
keep as short as possible.
5. Locate the VCCandBOOSTcapacitorsincloseproximity
to the IC. These capacitors carry the MOSFET driver’s high
peak currents. Place the small signal components away
from high frequency switching nodes (BOOST, SW, and
TG). In the layout shown in Figure 9, place all the small
signal components on one side of the IC and all the power
components on the other. This helps to keep the signal
and power grounds separate.
6. A small decoupling capacitor (100pF) is sometimes
useful for filtering high frequency noise on the feedback
and sense nodes. If used, locate as close to the IC as
possible.
7. The LT3724 packaging will efficiently remove heat from
the IC through the exposed pad on the backside of the part.
The exposed pad is soldered to a copper footprint on the
PCB. Make this footprint as large as possible to improve
the thermal resistance of the IC case to ambient air. This
helps to keep the LT3724 at a lower temperature.
8. Make the trace connecting the gate of MOSFET M1 to
the TG pin of the LT3724 short and wide.
相關PDF資料 |
PDF描述 |
|---|---|
| LT3740EDHC | 0.14 A SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, PDSO16 |
| LT3741EFE#PBF | SWITCHING CONTROLLER, 1070 kHz SWITCHING FREQ-MAX, PDSO20 |
| LT3741IFE#TRPBF | SWITCHING CONTROLLER, 1070 kHz SWITCHING FREQ-MAX, PDSO20 |
| LT3741EUF#PBF | SWITCHING CONTROLLER, 1070 kHz SWITCHING FREQ-MAX, PQCC20 |
| LT3741EUF#TRPBF | SWITCHING CONTROLLER, 1070 kHz SWITCHING FREQ-MAX, PQCC20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3726EGN | 制造商:Linear Technology 功能描述: |
| LT373L | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
| LT373LF | 制造商:EDSYN 功能描述:LONER Angle Face Soldring Tip High-Temperature Rated for Lead-Free Process W: .0 |
| LT373L-UR | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
發布緊急采購，3分鐘左右您將得到回復。