- 您現在的位置：買賣IC網 > PDF目錄44984 > LT3485EDD-0#TRPBF (LINEAR TECHNOLOGY CORP) SPECIALTY ANALOG CIRCUIT, PDSO10 PDF資料下載
參數資料
| 型號： | LT3485EDD-0#TRPBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| 封裝： | 3 X 3 MM, LEAD FREE, PLASTIC, MO-229WEED-2, DFN-10 |
| 文件頁數： | 2/20頁 |
| 文件大?。?/td> | 339K |
| 代理商： | LT3485EDD-0#TRPBF |
LT3485-0/LT3485-1/
LT3485-2/LT3485-3
10
34850123fb
APPLICATIO S I FOR ATIO
WU
U
Choosing the Right Device
(LT3485-0/LT3485-1/LT3485-2/LT3485-3)
The only difference between the four versions of the
LT3485 is the peak current level. For the fastest possible
charge time, use the LT3485-3. The LT3485-1 has the
lowest peak current capability, and is designed for
applications that need a more limited drain on the
batteries. Due to the lower peak current, the LT3485-1 can
use a physically smaller transformer. The LT3485-0 and
LT3485-2 have a current limit in between that of the
LT3485-3 and the LT3485-1.
Transformer Design
The flyback transformer is a key element for any
LT3485-0/LT3485-1/LT3485-2/LT3485-3 design. It must
be designed carefully and checked that it does not cause
excessive current or voltage on any pin of the part. The
main parameters that need to be designed are shown in
Table 1.
The first transformer parameter that needs to be set is the
turns ratio N. The LT3485-0/LT3485-1/LT3485-2/LT3485-
3 accomplish output voltage detection by monitoring the
flyback waveform on the SW pin. When the SW voltage
reaches 31.5V higher than the VBAT voltage, the part will
halt power delivery. Thus, the choice of N sets the target
output voltage as it changes the amplitude of the reflected
voltage from the output to the SW pin. Choose N accord-
ing to the following equation:
N
VOUT
=
+ 2
31 5
.
where VOUT is the desired output voltage. The number 2
in the numerator is used to include the effect of the voltage
drop across the output diode(s).
Thus for a 320V output, N should be 322/31.5 or 10.2. For
a 300V output, choose N equal to 302/31.5 or 9.6.
The next parameter that needs to be set is the primary
inductance, LPRI. Choose LPRI according to the following
formula:
L
V
NI
PRI
OUT
PK
≥
200 10 9
where VOUT is the desired output voltage. N is the trans-
former turns ratio. IPK is 1.4 (LT3485-0), 0.7 (LT3485-1),
1 (LT3485-2) and 2 (LT3485-3).
LPRI needs to be equal or larger than this value to ensure
that the LT3485-0/LT3485-1/LT3485-2/LT3485-3 has ad-
equate time to respond to the flyback waveform.
All other parameters need to meet or exceed the recom-
mended limits as shown in Table 1. A particularly impor-
tant parameter is the leakage inductance, LLEAK. When the
power switch of the LT3485-0/LT3485-1/LT3485-2/
LT3485-3 turns off, the leakage inductance on the pri-
mary of the transformer causes a voltage spike to occur
on the SW pin. The height of this spike must not exceed
40V, even though the absolute maximum rating of the SW
Pin is 50V. The 50V absolute maximum rating is a DC
blocking voltage specification, which assumes that the
current in the power NPN is zero. Figure 3 shows the SW
voltage waveform for the circuit of Figure 8 (LT3485-0).
Table 1. Recommended Transformer Parameters
TYPICAL RANGE
PARAMETER
NAME
LT3485-0
LT3485-1
LT3485-2
LT3485-3
UNITS
LPRI
Primary Inductance
>5
>10
>7
>3.5
H
LLEAK
Primary Leakage Inductance
100 to 300
200 to 500
100 to 300
nH
N
Secondary: Primary Turns Ratio
8 to 12
VISO
Secondary to Primary Isolation Voltage
>500
V
ISAT
Primary Saturation Current
>1.6
>0.8
>1.0
>2
A
RPRI
Primary Winding Resistance
<300
<500
<400
<200
m
RSEC
Secondary Winding Resistance
<40
<80
<60
<30
相關PDF資料 |
PDF描述 |
|---|---|
| LT3485EDD-0#TR | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| LT3493EDCB-3#TR | 2.2 A SWITCHING REGULATOR, 815 kHz SWITCHING FREQ-MAX, PDSO6 |
| LT3494EDDB#PBF | 0.25 A SWITCHING REGULATOR, PDSO8 |
| LT3494EDDB | 0.25 A SWITCHING REGULATOR, PDSO8 |
| LT3502AEDC#PBF | 1.1 A SWITCHING REGULATOR, 2800 kHz SWITCHING FREQ-MAX, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3485EDD-1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Photoflash Capacitor Chargers with Output Voltage Monitor and Integrated IGBT Drive |
| LT3485EDD-1#PBF | 功能描述:IC CHARGER PHOTOFLASH 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
| LT3485EDD-1#TRPBF | 功能描述:IC CHARGER PHOTOFLASH 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
| LT3485EDD-2 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Photoflash Capacitor Chargers with Output Voltage Monitor and Integrated IGBT Drive |
| LT3485EDD-2#PBF | 功能描述:IC CHARGER PHOTOFLASH 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
發(fā)布緊急采購，3分鐘左右您將得到回復。