- 您現在的位置：買賣IC網 > PDF目錄5921 > LT1993IUD-4#PBF (Linear Technology)IC DIFF AMP/ADC DRVR 16-QFN PDF資料下載
參數資料
| 型號： | LT1993IUD-4#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 4/16頁 |
| 文件大小： | 0K |
| 描述： | IC DIFF AMP/ADC DRVR 16-QFN |
| 標準包裝： | 121 |
| 放大器類型： | 差分 |
| 電路數： | 2 |
| 輸出類型： | 差分 |
| 轉換速率： | 1100 V/µs |
| -3db帶寬： | 900MHz |
| 電流 - 輸入偏壓： | 5µA |
| 電壓 - 輸入偏移： | 1000µV |
| 電流 - 電源： | 100mA |
| 電流 - 輸出 / 通道： | 45mA |
| 電壓 - 電源，單路/雙路(±)： | 4 V ~ 5.5 V，±2 V ~ 2.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 16-QFN-EP（3x3） |
| 包裝： | 管件 |
| 產品目錄頁面： | 1322 (CN2011-ZH PDF) |
LT1993-4
12
19934fa
APPLICATIO S I FOR ATIO
WU
U
Single-Ended to Differential Operation
The LT1993-4’s performance with single-ended inputs is
comparable to its performance with differential inputs.
This excellent single-ended performance is largely due
to the internal topology of the LT1993-4. Referring to
the block diagram, if the +INA and +INB pins are driven
with a single-ended signal (while –INA and –INB are tied
to AC ground), then the +OUT and –OUT pins are driven
differentially without any voltage swing needed from
amplier C. Single-ended to differential conversion using
more conventional topologies suffers from performance
limitations due to the common mode amplier.
Driving ADCs
The LT1993-4 has been specically designed to interface
directly with high speed Analog to Digital Converters
(ADCs). In general, these ADCs have differential inputs,
with an input impedance of 1k or higher. In addition, there
is generally some form of lowpass or bandpass ltering just
prior to the ADC to limit input noise at the ADC, thereby
improving system signal to noise ratio. Both the unltered
and ltered outputs of the LT1993-4 can easily drive the
high impedance inputs of these differential ADCs. If the
ltered outputs are used, then cutoff frequency and the
type of lter can be tailored for the specic application if
needed.
Wideband Applications
(Using the +OUT and –OUT Pins)
In applications where the full bandwidth of the LT1993-4
is desired, the unltered output pins (+OUT and –OUT)
should be used. They have a low output impedance;
therefore, gain is unaffected by output load. Capacitance
in excess of 5pF placed directly on the unltered outputs
results in additional peaking and reduced performance.
When driving an ADC directly, a small series resistance
is recommended between the LT1993-4’s outputs and
the ADC inputs (Figure 4). This resistance helps eliminate
any resonances associated with bond wire inductances of
either the ADC inputs or the LT1993-4’s outputs. A value
between 10
Ω and 25Ω gives excellent results.
Filtered Applications
(Using the +OUTFILTERED and –OUTFILTERED Pins)
Filtering at the output of the LT1993-4 is often desired to
provide either anti-aliasing or improved signal to noise
ratio. To simplify this ltering, the LT1993-4 includes an
additional pair of differential outputs (+OUTFILTERED and
–OUTFILTERED) which incorporate an internal lowpass
lter network with a –3dB bandwidth of 175MHz (Figure
5). These pins each have an output impedance of 25
Ω. In-
ternal capacitances are 12pF to VEE on each ltered output,
plus an additional 12pF capacitor connected differentially
between the two ltered outputs. This resistor/capaci-
tor combination creates ltered outputs that look like a
series 25
Ω resistor with a 36pF capacitor shunting each
ltered output to AC ground, giving a –3dB bandwidth of
175MHz.
19934 F04
LT1993-4
–OUT
+OUT
8
5
10
TO 25
10
TO 25
ADC
Figure 4. Adding Small Series R at LT1993-4 Output
The lter cutoff frequency is easily modied with just a
few external components. To increase the cutoff frequency,
simply add 2 equal value resistors, one between +OUT and
+OUTFILTERED and the other between –OUT and –OUTFIL-
TERED (Figure 6). These resistors are in parallel with the
internal 25
Ω resistor, lowering the overall resistance and
increasing lter bandwidth. To double the lter bandwidth,
for example, add two external 25
Ω resistors to lower
the series resistance to 12.5
Ω. The 36pF of capacitance
remains unchanged, so lter bandwidth doubles.
Figure 5. LT1993-4 Internal Filter Topology –3dB BW ≈175MHz
19934 F05
VEE
12pF
LT1993-4
–OUT
25
9
25
9
+OUT
12pF
–OUTFILTERED
+OUTFILTERED
8
7
6
5
FILTERED OUTPUT
(175MHz)
相關PDF資料 |
PDF描述 |
|---|---|
| ADA4817-1ARDZ-R7 | IC OPAMP VF 410MHZ LN 40MA 8SOIC |
| OP284FSZ-REEL7 | IC OPAMP GP R-R 4.25MHZ LN 8SOIC |
| AD8295ACPZ-WP | IC AMP INST 1MHZ TRPL LN 16LFCSP |
| GTCS25-900M-R02 | GAS TUBE 5MM 90V 20% 2.5KA SMD |
| 961103-6700-AR-TP | CONN HEADER VERT 3POS GOLD SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1994 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Precision, Low Power Rail-to-Rail Input/Output |
| LT1994CDD | 制造商:Linear Technology 功能描述:SC-Amps/High Speed, 70MHz Low Noise/Distortion Differential Amplifer |
| LT1994CDD#PBF | 功能描述:IC DIFF AMP/DRIVER LN 8-DFN RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT |
| LT1994CDD#PBF | 制造商:Linear Technology 功能描述:Operational Amplifier (Op-Amp) IC 制造商:Linear Technology 功能描述:IC, DIFFERENTIAL AMP, 70MHZ, 65V/ uS DFN8 |
| LT1994CDD#TR | 制造商:Linear Technology 功能描述:DIFF-AMPLIFIER, 70MHZ, 65V/US, DFN-8, No. of Amplifiers:1, Input Offset Voltage: 制造商:Linear Technology 功能描述:DIFF-AMPLIFIER, 70MHZ, 65V/US, DFN-8, No. of Amplifiers:1, Input Offset Voltage:2mV, Bandwidth:70MHz, Amplifier Case Style:DFN, No. of Pins:8, Supply Voltage Range:2.375V to 12.6V, Slew Rate:65V/s, Supply Current:14.8mA, MSL:- , RoHS Compliant: No |
發布緊急采購，3分鐘左右您將得到回復。