- 您現在的位置：買賣IC網 > PDF目錄385499 > LT1239 (Linear Technology Corporation) Backup Battery Management Circuit(后備電池管理電路) PDF資料下載
參數資料
| 型號： | LT1239 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Backup Battery Management Circuit(后備電池管理電路) |
| 中文描述： | 備份電池管理電路（后備電池管理電路） |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 211K |
| 代理商： | LT1239 |
6
LT1239
PI
FU
CTIO
N
S
U
U
ADJ (Pin 1):
Adjust Pin of Regulator 1. The regulator will
servo the adjust pin to 3.75V referred to ground. Bias
current will be approximately 50nA and will flow into the
adjust pin.
GND (Pin 2):
Ground Pin for Regulator 1. Note that the
three ground pins (pins 2, 4, 5) are connected together
internally and should all be grounded externally.
SHDN1 (Pin 3):
Shutdown Pin for Regulator 1. Regulator
1 output will be on if the shutdown pin is either: 1) Left
floating (open circuit) or 2) pulled up to the 5V rail. If the
shutdown function is not used, the shutdown pin is nor-
mally left open circuit. Regulator 1 output will be off if the
shutdown pin is pulled to ground. The shutdown pin
current with the pin pulled to ground will be in the range of
2
μ
A flowing out of the pin. The shutdown pin current with
the pin pulled up to 5V will be zero.
GND (Pin 4):
Ground. This ground pin is tied to the
substrate of the die, between regulator 1 and the rest of the
circuit. It is used as an isolation barrier between regulator
1 and the rest of the circuitry.
GND (Pin 5):
Ground Pin for Regulator 2.
SHDN2 (Pin 6):
Shutdown Pin for Regulator 2. Regulator
2 output will be on if the shutdown pin is either: 1) Left
floating (open circuit) or 2) pulled up to the 5V rail. If the
shutdown function is not used, the shutdown pin is nor-
mally left open circuit. Regulator 2 output will be off if the
shutdown pin is pulled to ground. The shutdown pin
current with the pin pulled to ground will be in the range of
2
μ
A flowing out of the pin. The shutdown pin current with
the pin pulled up to 5V will be zero.
E/A (IN) (Pin 7):
Noninverting Input of the Error Amplifier.
This pin should be tied to the center tap point in the output
divider for regulator 1. The bias current for this pin will be
in the range of 3nA and it will flow out of the pin.
E/A (OUT) (Pin 8):
Output of the Error Amplifier. This is
normally connected to the center tap of the backup cells.
NC (Pin 9):
Not Connected.
INPUT 2 (Pin 10):
Input Pin (V
CC
) for Regulator 2, the Error
Amplifier, and the Low-Battery Detection Circuit.
I
MON
2 (Pin 11):
Current Monitor Pin for Regulator 2. If the
current monitor function is not used, this pin should be
tied to the output pin of regulator 2.
OUT 2 (Pin 12):
Output of Regulator 2. It is also the
inverting input and output of the comparator. If the main
5V system supply is up and running then the comparator
output will pull the output of regulator 2 up to 5V.
5V
IN
(Pin 13):
Noninverting Input of the comparator and
the collector of the output driver. The collector of the
output driver is normally connected to the main 5V system
supply.
INPUT 1 (Pin 14):
Input Pin (V
CC
) of Regulator 1.
I
MON
1 (Pin 15):
Current Monitor Pin for Regulator 1. The
current flowing out of this pin will be approximately 1/200
of the output current of regulator 1. If the current monitor
function is not used, this pin should be tied to the output
pin of regulator 1.
OUT 1 (Pin 16):
Output of Regulator 1.
Regulator 1:
Regulator 1 is used to supply the charging
current to the backup batteries. It converts the voltage on
the main battery to a fixed output voltage to charge the
backup cells. The output voltage is set with a voltage
divider connected between the output and ground with a
tap point of the divider connected to the adjust pin. The
regulator servos its output in order to maintain the adjust
pin at 3.75V referred to ground. The resistor divider
should be chosen such that the divider current is approxi-
mately 5
μ
A. This means the impedance from the adjust pin
to ground should be approximately 750k
. For safety
requirements a resistor can be placed between the output
pin and the top of the divider that sets the regulated output
voltage. The regulator will regulate the voltage at the top of
the divider. Quiescent current will be 10
μ
A to 15
μ
A. Output
short-circuit current will be approximately 70mA.
FU
CTIO
AL DESCRIPTIO
U
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LT1241 Series | High Speed Current Mode Pulse Width Modulators(高速，電流模式脈寬調制器) |
| LT1248 | Octal D-Type Transparent Latches with 3-state Outputs 20-SO 0 to 70 |
| LT1248C | Octal D-Type Transparent Latches with 3-state Outputs 20-SO 0 to 70 |
| LT1248CN | Octal D-Type Transparent Latches with 3-state Outputs 20-SO 0 to 70 |
| LT1248CS | Replaced by SN74ALS374A : Octal D-Type Edge Triggered Flip-Flops with 3-State Outputs 20-SSOP 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1239_02 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Backup Battery Management Circuit |
| LT1239CS | 功能描述:IC BATT BACKUP MNGMNT SYS 16SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| LT123A | 制造商:LINER 制造商全稱:Linear Technology 功能描述:5 Volt, 3 Amp Voltage Regulator |
| LT123AK | 制造商:LINER 制造商全稱:Linear Technology 功能描述:5 Volt, 3 Amp Voltage Regulator |
| LT123AK/883 | 制造商:Linear Technology 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。