- 您現在的位置：買賣IC網 > PDF目錄385499 > LT1239 (Linear Technology Corporation) Backup Battery Management Circuit(后備電池管理電路) PDF資料下載
參數資料
| 型號： | LT1239 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Backup Battery Management Circuit(后備電池管理電路) |
| 中文描述： | 備份電池管理電路（后備電池管理電路） |
| 文件頁數： | 4/12頁 |
| 文件大?。?/td> | 211K |
| 代理商： | LT1239 |
4
LT1239
ELECTRICAL CHARACTERISTICS
PARAMETER
Offset Voltage
Output Current Sourcing
CONDITIONS
MIN
TYP
0
5
5
MAX
15
UNITS
mV
mA
mA
G
V
IN2
= 6.8V, V
E/A(IN)
= 3.4V, T
J
= 25
°
C
V
IN2
= 6.8V, V
E/A(IN)
= 3.4V, T
J
= 25
°
C
3
3
Sinking
Regulator 2, Low Battery Detector and Error Amplifier
Quiescent Current
V
IN2
= 6.8V, 5V
IN
= 0V, V
E/A(IN)
= 3.4V
V
IN2
= 6.8V, 5V
IN
= 0V, V
E/A(IN)
= 3.4V, V
PIN6
= 0V
V
IN2
= 4.8V, 5V
IN
= 0V, V
E/A(IN)
= 2.4V
G
G
G
20
8
3
30
12
6
μ
A
μ
A
μ
A
The
G
denotes specifications which apply over the full operating
temperature range.
Note 1:
All voltages are with respect to the ground pins of the device
(pins 2, 4, 5) unless otherwise specified.
Note 2:
The shutdown pin input voltage rating is required for a low
impedance source. Internal protection devices connected to the shutdown
pin will turn on and clamp the pin to approximately 7V or –0.6V. This
range allows the use of 5V logic devices to drive the pin directly. For high
impedance sources or logic running on supply voltages greater than 5.5V,
the maximum current driven into the shutdown pin must be limited to
5mA.
Note 3:
The current monitor pin for regulator 1 (pin 15) can be pulled 30V
below the input pin (pin 14). The current monitor pin must not be pulled
above the input pin.
Note 4:
The current monitor pin for regulator 2 (pin 11) can be pulled 30V
below the input pin (pin 10). The current monitor pin must not be pulled
above the input pin.
Note 5:
E/A (OUT) pin should not be pulled below ground or above
the voltage at Input 2.
Note 6:
The device is specified to an operating temperature range of 0
°
C to
70
°
C. The device is guaranteed to be functional up to the thermal
shutdown temperature. The thermal shutdown temperature for this device
is approximately 100
°
C.
Note 7:
Operating conditions are limited by maximum junction
temperature. The regulated output specification will not apply for all
possible combinations of input voltage and output current. When
operating at maximum output current, the input voltage range must be
limited. When operating at maximum input voltage, the output current
range must be limited.
Note 8:
Regulator 1 of the LT1239 is tested and specified with the adjust
pin (pin 1) tied to the output pin (pin 16). See Applications Information.
Note 9:
Dropout voltage is the minimum input/output voltage required to
maintain regulation at the specified output current. In dropout, the output
voltage measured at the package pins will be equal to (V
IN
– V
DROPOUT
).
Note 10:
The quiescent current of the comparator is included in the
ground pin current and quiescent current specifications for regulator 1.
The comparator output is turned off (pin 13 = 0V, pin 12 = 5V) during
these tests.
Note 11:
Ground pin current for regulator 1 is tested with V
IN
= V
OUT
(nominal) and a current source load. This means that the device is tested
in it’s dropout region. Ground pin current will decrease slightly at higher
input voltages.
Note 12:
Adjust pin current flows into the adjust pin.
Note 13:
Shutdown pin current at V
SHDN
= 0V flows out of
the shutdown pin.
Note 14:
6.8V is the nominal voltage of two lithium-ion cells.
TYPICAL PERFOR
M
A
CE CHARACTERISTICS
U
Low-Battery Detector Thresholds
vs Temperature
Regulator 2 Output Voltage vs
Temperature
Regulator 1 Adjust Pin Voltage vs
Temperature
TEMPERATURE (
°
C)
–50
25
75
LT1239 TPC01
–25
0
50
100
L 5.60
4.90
5.50
5.40
5.30
5.20
5.10
5.00
START-UP THRESHOLD
SHUTDOWN THRESHOLD
TEMPERATURE (
°
C)
–50
R
–25
0
25
50
LT1239 TPC02
75
4.975
4.950
4.925
4.900
4.875
4.850
4.825
4.800
4.775
4.750
4.725
100
TEMPERATURE (
°
C)
–50
A
–25
0
25
50
LT1239 TPC03
75
3.80
3.79
3.78
3.77
3.76
3.75
3.74
3.73
3.72
3.71
3.70
100
相關PDF資料 |
PDF描述 |
|---|---|
| LT1241 Series | High Speed Current Mode Pulse Width Modulators(高速，電流模式脈寬調制器) |
| LT1248 | Octal D-Type Transparent Latches with 3-state Outputs 20-SO 0 to 70 |
| LT1248C | Octal D-Type Transparent Latches with 3-state Outputs 20-SO 0 to 70 |
| LT1248CN | Octal D-Type Transparent Latches with 3-state Outputs 20-SO 0 to 70 |
| LT1248CS | Replaced by SN74ALS374A : Octal D-Type Edge Triggered Flip-Flops with 3-State Outputs 20-SSOP 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1239_02 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Backup Battery Management Circuit |
| LT1239CS | 功能描述:IC BATT BACKUP MNGMNT SYS 16SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| LT123A | 制造商:LINER 制造商全稱:Linear Technology 功能描述:5 Volt, 3 Amp Voltage Regulator |
| LT123AK | 制造商:LINER 制造商全稱:Linear Technology 功能描述:5 Volt, 3 Amp Voltage Regulator |
| LT123AK/883 | 制造商:Linear Technology 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。