- 您現在的位置：買賣IC網 > PDF目錄385499 > LT1210 (Linear Technology Corporation) 1.1A, 35MHz Current Feedback Amplifier PDF資料下載
參數資料
| 型號： | LT1210 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 1.1A, 35MHz Current Feedback Amplifier |
| 中文描述： | 1.1A的，至35MHz電流反饋放大器 |
| 文件頁數： | 8/16頁 |
| 文件大小： | 358K |
| 代理商： | LT1210 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
8
LT1210
U
S
A
The LT1210 is a current feedback amplifier with high
output current drive capability. The device is stable with
large capacitive loads and can easily supply the high
currents required by capacitive loads. The amplifier will
drive low impedance loads such as cables with excellent
linearity at high frequencies.
O
PPLICATI
U
U
Feedback Resistor Selection
The optimum value for the feedback resistors is a function
of the operating conditions of the device, the load imped-
ance and the desired flatness of response. The Typical AC
Performance tables give the values which result in less
than 1dB of peaking for various resistive loads and oper-
ating conditions. If this level of flatness is not required, a
higher bandwidth can be obtained by use of a lower
feedback resistor. The characteristic curves of Bandwidth
vs Supply Voltage indicate feedback resistors for peaking
up to 5dB. These curves use a solid line when the response
has less than 1dB of peaking and a dashed line when the
response has 1dB to 5dB of peaking. The curves stop
where the response has more than 5dB of peaking.
For resistive loads, the COMP pin should be left open (see
Capacitive Loads section).
Capacitive Loads
The LT1210 includes an optional compensation network
for driving capacitive loads. This network eliminates most
of the output stage peaking associated with capacitive
loads, allowing the frequency response to be flattened.
Figure 1 shows the effect of the network on a 200pF load.
Without the optional compensation, there is a 6dB peak at
40MHz caused by the effect of the capacitance on the
output stage. Adding a 0.01
μ
F bypass capacitor between
the output and the COMP pins connects the compensation
and greatly reduces the peaking. A lower value feedback
resistor can now be used, resulting in a response which is
flat to
±
1dB to 40MHz. The network has the greatest effect
for C
L
in the range of 0pF to 1000pF. The graphs of
Bandwidth and Feedback Resistance vs Capacitive Load
can be used to select the appropriate value of feedback
resistor. The values shown are for 1dB and 5dB peaking at
a gain of 2 with no resistive load. This is a worst-case
condition, as the amplifier is more stable at higher gains
and with some resistive load in parallel with the capaci-
FREQUENCY (MHz)
1
–6
V
–2
2
6
10
10
100
1210 F01
–4
0
4
8
12
14
V
S
=
±
15V
C
L
= 200pF
R
= 1.5k
COMPENSATION
R
= 3.4k
NO COMPENSATION
R
= 3.4k
COMPENSATION
Figure 1
tance. Also shown is the –3dB bandwidth with the sug-
gested feedback resistor vs the load capacitance.
Although the optional compensation works well with
capacitive loads, it simply reduces the bandwidth when it
is connected with resistive loads. For instance, with a 10
load, the bandwidth drops from 35MHz to 26MHz when
the compensation is connected. Hence, the compensation
was made optional. To disconnect the optional compensa-
tion, leave the COMP pin open.
Shutdown/Current Set
If the shutdown feature is not used, the SHUTDOWN pin
must be connected to ground or V
–
.
The Shutdown pin can be used to either turn off the biasing
for the amplifier, reducing the quiescent current to less
than 200
μ
A, or to control the quiescent current in normal
operation.
The total bias current in the LT1210 is controlled by the
current flowing out of the Shutdown pin. When the Shut-
down pin is open or driven to the positive supply, the part
is shut down. In the shutdown mode, the output looks like
a 70pF capacitor and the supply current is typically less
than 100
μ
A. The Shutdown pin is referenced to the posi-
tive supply through an internal bias circuit (see the Simpli-
fied Schematic). An easy way to force shutdown is to use
open-drain (collector) logic. The circuit shown in Figure 2
uses a 74C904 buffer to interface between 5V logic and the
LT1210. The switching time between the active and shut-
down states is about 1
μ
s.
A 24k pull-up resistor speeds
相關PDF資料 |
PDF描述 |
|---|---|
| LT1210CR | 1.1A, 35MHz Current Feedback Amplifier |
| LT1210CS | 9-Bit Bus Transceivers With 3-State Outputs 24-PDIP 0 to 70 |
| LT1210CT7 | 1.1A, 35MHz Current Feedback Amplifier |
| LT1211 | 14MHz,7V/ms,Single Supply Dual Precision Op Amps(14MHz,7V/ms,單電源，雙路精密運算放大器) |
| LT1212 | 14MHz,7V/ms,Single Supply Quad Precision Op Amps(14MHz,7V/ms,單電源，四路精密運算放大器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1210_06 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.1A, 35MHz Current Feedback Amplifier |
| LT1210CR | 功能描述:IC 35MHZ 1.1 AMP AMPLIFIER 7 DD RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:Excalibur™ 放大器類型:J-FET 電路數:1 輸出類型:- 轉換速率:45 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:20pA 電壓 - 輸入偏移:490µV 電流 - 電源:1.7mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:帶卷 (TR) |
| LT1210CR#PBF | 功能描述:IC 35MHZ 1.1 AMP AMPLIFIER 7 DD RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源，單路/雙路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| LT1210CR#PBF | 制造商:Linear Technology 功能描述:IC, OP-AMP, 55MHZ, 900V/s, 3mV, 7-TO-26 |
| LT1210CR#TR | 功能描述:IC AMP CURR FEEDBACK 1.1A 7DD RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:Excalibur™ 放大器類型:J-FET 電路數:1 輸出類型:- 轉換速率:45 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:20pA 電壓 - 輸入偏移:490µV 電流 - 電源:1.7mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。