- 您現在的位置：買賣IC網 > PDF目錄385499 > LT1210 (Linear Technology Corporation) 1.1A, 35MHz Current Feedback Amplifier PDF資料下載
參數資料
| 型號： | LT1210 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 1.1A, 35MHz Current Feedback Amplifier |
| 中文描述： | 1.1A的，至35MHz電流反饋放大器 |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 358K |
| 代理商： | LT1210 |
11
LT1210
U
S
A
O
PPLICATI
IU
U
Power Supplies
The LT1210 will operate from single or split supplies from
±
5V (10V total) to
±
15V (30V total). It is not necessary to
use equal value split supplies, however the offset voltage
and inverting input bias current will change. The offset
voltage changes about 500
μ
V per volt of supply mis-
match. The inverting bias current can change as much as
5
μ
A per volt of supply mismatch, though typically the
change is less than 0.5
μ
A per volt.
Power Supply Bypassing
To obtain the maximum output and the minimum distor-
tion from the LT1210, the power supply rails should be
well bypassed. For example, with the output stage pouring
1A current peaks into the load, a 1
power supply imped-
ance will cause a droop of 1V, reducing the available
output swing by that amount. Surface mount tantalum and
ceramic capacitors make excellent low ESR bypass ele-
ments when placed close to the chip. For frequencies
above 100kHz, use 1
μ
F and 100nF ceramic capacitors.
If significant power must be delivered below 100kHz,
capacitive reactance becomes the limiting factor. Larger
ceramic or tantalum capacitors, such as 4.7
μ
F, are recom-
mended in place of the 1
μ
F unit mentioned above.
Inadequate bypassing is evidenced by reduced output
swing and “distorted” clipping effects when the output is
driven to the rails. If this is observed, check the supply pins
of the device for ripple directly related to the output
waveform. Significant supply modulation indicates poor
bypassing.
Thermal Considerations
The LT1210 contains a thermal shutdown feature which
protects against excessive internal (junction) tempera-
ture. If the junction temperature of the device exceeds the
protection threshold, the device will begin cycling be-
tween normal operation and an off state. The cycling is not
harmful to the part. The thermal cycling occurs at a slow
rate, typically 10ms to several seconds, which depends on
the power dissipation and the thermal time constants of
the package and heat sinking. Raising the ambient tem-
perature until the device begins thermal shutdown gives a
good indication of how much margin there is in the
thermal design.
COPPER AREA
For surface mount devices heat sinking is accomplished
by using the heat spreading capabilities of the PC board
and its copper traces. Experiments have shown that the
heat spreading copper layer does not need to be electri-
cally connected to the tab of the device. The PCB material
can be very effective at transmitting heat between the pad
area attached to the tab of the device, and a ground or
power plane layer either inside or on the opposite side of
the board. Although the actual thermal resistance of the
PCB material is high, the length/area ratio of the thermal
resistance between the layer is small. Copper board stiff-
eners and plated through holes can also be used to spread
the heat generated by the device.
Tables 1 and 2 list thermal resistance for each package. For
the TO-220 package, thermal resistance is given for junc-
tion-to-case only since this package is usually mounted to
a heat sink. Measured values of thermal resistance for
several different board sizes and copper areas are listed for
each surface mount package. All measurements were
taken in still air on 3/32" FR-4 board with 2 oz copper. This
data can be used as a rough guideline in estimating
thermal resistance. The thermal resistance for each appli-
cation will be affected by thermal interactions with other
components as well as board size and shape.
Table 1. R Package, 7-Lead DD
THERMAL RESISTANCE
(JUNCTION-TO-AMBIENT)
25
°
C/W
27
°
C/W
35
°
C/W
TOPSIDE*
2500 sq. mm
1000 sq. mm
125 sq. mm
*Tab of device attached to topside copper
BACKSIDE
2500 sq. mm
2500 sq. mm
2500 sq. mm
BOARD AREA
2500 sq. mm
2500 sq. mm
2500 sq. mm
Table 2. Fused 16-Lead SO Package
COPPER AREA
THERMAL RESISTANCE
(JUNCTION-TO-AMBIENT)
40
°
C/W
46
°
C/W
48
°
C/W
49
°
C/W
56
°
C/W
58
°
C/W
59
°
C/W
60
°
C/W
61
°
C/W
TOPSIDE
2500 sq. mm
1000 sq. mm
600 sq. mm
180 sq. mm
180 sq. mm
180 sq. mm
180 sq. mm
180 sq. mm
180 sq. mm
BACKSIDE
2500 sq. mm
2500 sq. mm
2500 sq. mm
2500 sq. mm
1000 sq. mm
600 sq. mm
300 sq. mm
100 sq. mm
0 sq. mm
BOARD AREA
5000 sq. mm
3500 sq. mm
3100 sq. mm
2680 sq. mm
1180 sq. mm
780 sq. mm
480 sq. mm
280 sq. mm
180 sq. mm
相關PDF資料 |
PDF描述 |
|---|---|
| LT1210CR | 1.1A, 35MHz Current Feedback Amplifier |
| LT1210CS | 9-Bit Bus Transceivers With 3-State Outputs 24-PDIP 0 to 70 |
| LT1210CT7 | 1.1A, 35MHz Current Feedback Amplifier |
| LT1211 | 14MHz,7V/ms,Single Supply Dual Precision Op Amps(14MHz,7V/ms,單電源，雙路精密運算放大器) |
| LT1212 | 14MHz,7V/ms,Single Supply Quad Precision Op Amps(14MHz,7V/ms,單電源，四路精密運算放大器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1210_06 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.1A, 35MHz Current Feedback Amplifier |
| LT1210CR | 功能描述:IC 35MHZ 1.1 AMP AMPLIFIER 7 DD RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:Excalibur™ 放大器類型:J-FET 電路數:1 輸出類型:- 轉換速率:45 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:20pA 電壓 - 輸入偏移:490µV 電流 - 電源:1.7mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:帶卷 (TR) |
| LT1210CR#PBF | 功能描述:IC 35MHZ 1.1 AMP AMPLIFIER 7 DD RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源，單路/雙路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| LT1210CR#PBF | 制造商:Linear Technology 功能描述:IC, OP-AMP, 55MHZ, 900V/s, 3mV, 7-TO-26 |
| LT1210CR#TR | 功能描述:IC AMP CURR FEEDBACK 1.1A 7DD RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:Excalibur™ 放大器類型:J-FET 電路數:1 輸出類型:- 轉換速率:45 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:20pA 電壓 - 輸入偏移:490µV 電流 - 電源:1.7mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。