- 您現在的位置：買賣IC網 > PDF目錄385498 > LT1082 (Linear Technology Corporation) 1A High Voltage, Efficiency Switching Voltage Regulator(１Ａ，高壓，高效率開關穩壓器) PDF資料下載
參數資料
| 型號： | LT1082 |
| 廠商： | Linear Technology Corporation |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 1A High Voltage, Efficiency Switching Voltage Regulator(１Ａ，高壓，高效率開關穩壓器) |
| 中文描述： | 1A條高電壓，效率開關穩壓器（1A中，高壓，高效率開關穩壓器） |
| 文件頁數： | 8/12頁 |
| 文件大小： | 212K |
| 代理商： | LT1082 |
8
LT1082
OPERATIOU
disconnect the main error amplifier output and connects
the output of the flyback amplifier to the comparator input.
The LT1082 will then regulate the value of the flyback pulse
with respect to the supply voltage. This flyback pulse is
directly proportional to output voltage in the traditional
transformer coupled flyback topology regulator. By
regulating the amplitude of the flyback pulse, the output
voltage can be regulated with no direct connection between
input and output. The output is fully floating up to the
breakdown voltage of the transformer windings. Multiple
floating outputs are easily obtained with additional
windings. A special delay network inside the LT1082
ignores the leakage inductance spike at the leading edge of
the flyback pulse to improve output regulation.
When I
FB
drawn out of the FB pin reaches 350
μ
A, the
LT1082 shifts the switching frequency down to 12kHz.
This unique feature provides high voltage short-circuit
protection in systems like the telecom 5V supplies with
input voltages down to –70V; lower frequency is needed
under short-circuit conditions with current mode switchers
because minimum “on” time cannot be forced below the
internally set blanking time. Referring to the telecom 5V
supply circuit on the front page, with output shorted to
ground, the V
FB
stays at 0.6V when sourcing I
FB
up to
1mA. If the FB pin is forced to source more than 1mA, the
frequency shifting function may be defeated. Therefore,
the minimum suggested value for R
FB
is 1k and the
maximum suggested value is 1.2k. Also, no capacitance
more than 1nF should be used on the FB pin, because it
may cause unstable switching frequency in this low
frequency mode.
The error signal developed at the comparator input is
brought out externally. This pin (V
C
) has four different
functions. It is used for frequency compensation, current
limit adjustment, soft starting, and total regulator shutdown.
During normal regulator operation this pin sits at a voltage
between 0.9V (low output current) and 2V (high output
current). The error amplifiers are current output (g
m
)
types, so this voltage can be externally clamped for
adjusting current limit. Likewise, a capacitor-coupled
external clamp will provide soft start. Switch duty cycle
goes to zero if the V
C
pin is pulled to ground through a
diode, placing the LT1082 in an idle mode. Pulling the V
C
pin below 0.15V causes total regulator shutdown, with
only 120
μ
A supply current for shutdown circuitry biasing.
See AN19 for full application details.
Extra Pins on the MiniDIP Packages
The miniDIP LT1082 has the emitters of the power
transistor brought out separately from the ground pin.
This eliminates errors due to ground pin voltage drops and
allows the user to reduce switch current limit by a factor
of 2:1 by leaving the second emitter (E2) disconnected.
The first emitter (E1) should always be connected to the
ground pin. Note that switch “on” resistance doubles
when E2 is left open, so efficiency will suffer somewhat
when switch currents exceed 100mA. Also, note that chip
dissipation will actually increasewith E2 open during
normal load operation, even though dissipation in current
limit mode will decrease See “Thermal Considerations.”
Thermal Considerations When Using the
MiniDIP Packages
The low supply current and high switch efficiency of the
LT1082 allow it to be used without a heat sink in most
applications when the TO-220 package is selected.
This package is rated at 50
°
C/W. The miniDIPs, however,
are rated at 100
°
C/W in ceramic (J) and 90
°
/W in plastic
(N).
Care should be taken for miniDIP applications to ensure
that the worst case input voltage and load current conditions
do not cause excessive die temperatures. The following
formulas can be used as a rough guide to calculate LT1082
power dissipation. For more details, the reader is referred
to Application Note 19 (AN19), “Efficiency Calculations”
section.
Average supply current (including driver current) is:
I
IN
≈
4.5mA + I
SW
(0.004 + DC/28)
I
SW
= switch current
DC = switch duty cycle
Switch power dissipation is given by:
P
SW
= (I
SW
)
2
R
SW
DC
R
SW
= LT1082 switch “on” resistance (1.2
maximum)
相關PDF資料 |
PDF描述 |
|---|---|
| LT1086 Series | 1.5A Low Dropout Positive Regulators Adjustable and Fixed 2.85V, 3.3V, 3.6V, 5V, 12V(1.5A，低壓差正輸出固定和可調穩壓器) |
| LT1088 | Wideband RMS-dc Converter Building Block(寬帶RMS-DC變換器組件) |
| LT1101 | Precision Micropower,Single Supply Instrmentation Amplifier(Fixed Gain=10 or 100)(精密，微功耗，單電源儀用放大器（固定增益=10或100）) |
| LT1106 | Micropower Step-Up DC/DC Converter for PCMCIA Card Flash Memory |
| LT1106CF | 4-Bit Synchronous Up/Down Binary Counters 16-PDIP 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1082CN8 | 功能描述:IC REG MULTI CONFIG 1A 8DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT1082CN8#PBF | 功能描述:IC REG MULTI CONFIG 1A 8DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LT1082CN8PBF | 制造商:Linear Technology 功能描述:Switching Regulator 1A 3-75V PDIP8 |
| LT1082CQ | 功能描述:IC REG MULTI CONFIG 1A D2PAK RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT1082CQ#PBF | 功能描述:IC REG MULTI CONFIG 1A D2PAK RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
發布緊急采購，3分鐘左右您將得到回復。