- 您現在的位置：買賣IC網 > PDF目錄367585 > LPC2294 (NXP Semiconductors N.V.) 16/32-bit ARM microcontrollers 256 kB ISP/IAP Flash with CAN, 10-bit ADC and external memory interface PDF資料下載
參數資料
| 型號： | LPC2294 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 16/32-bit ARM microcontrollers 256 kB ISP/IAP Flash with CAN, 10-bit ADC and external memory interface |
| 中文描述： | 16/32位ARM微控制器的256 KB的供應商/聯合會與CAN，10閃光位模數轉換器和外部存儲器接口 |
| 文件頁數： | 26/40頁 |
| 文件大?。?/td> | 188K |
| 代理商： | LPC2294 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
Philips Semiconductors
LPC2292/LPC2294
16/32-bit ARM microcontrollers with external memory interface
Preliminary data
Rev. 01 — 05 February 2004
26 of 40
9397 750 12748
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
6.21.5
Memory Mapping Control
The Memory Mapping Control alters the mapping of the interrupt vectors that appear
beginning at address 0x00000000. Vectors may be mapped to the bottom of the
on-chip Flash memory, or to the on-chip static RAM. This allows code running in
different memory spaces to have control of the interrupts.
6.21.6
Power Control
The LPC2292/LPC2294 support two reduced power modes: Idle mode and
Power-down mode. In Idle mode, execution of instructions is suspended until either a
Reset or interrupt occurs. Peripheral functions continue operation during Idle mode
and may generate interrupts to cause the processor to resume execution. Idle mode
eliminates power used by the processor itself, memory systems and related
controllers, and internal buses.
In Power-down mode, the oscillator is shut down and the chip receives no internal
clocks. The processor state and registers, peripheral registers, and internal SRAM
values are preserved throughout Power-down mode and the logic levels of chip
output pins remain static. The Power-down mode can be terminated and normal
operation resumed by either a Reset or certain specific interrupts that are able to
function without clocks. Since all dynamic operation of the chip is suspended,
Power-down mode reduces chip power consumption to nearly zero.
A Power Control for Peripherals feature allows individual peripherals to be turned off if
they are not needed in the application, resulting in additional power savings.
6.21.7
VPB bus
The VPB Divider determines the relationship between the processor clock (cclk) and
the clock used by peripheral devices (PCLK). The VPB Divider serves two purposes.
The first is that the VPB bus cannot operate at the highest speeds of the CPU. In
order to compensate for this, the VPB bus may be slowed down to one half or one
fourth of the processor clock rate. The default condition at reset is for the VPB bus to
run at one quarter of the CPU clock. The second purpose of the VPB Divider is to
allow power savings when an application does not require any peripherals to run at
the full processor rate. Because the VPB Divider is connected to the PLL output, the
PLL remains active (if it was running) during Idle mode.
6.22 Emulation and debugging
The LPC2292/LPC2294 support emulation and debugging via a JTAG serial port. A
trace port allows tracing program execution. Debugging and trace functions are
multiplexed only with GPIOs on Port 1. This means that all communication, timer and
interface peripherals residing on Port 0 are available during the development and
debugging phase as they are when the application is run in the embedded system
itself.
6.22.1
Embedded ICE
Standard ARM EmbeddedICE logic provides on-chip debug support. The debugging
of the target system requires a host computer running the debugger software and an
EmbeddedICE protocol convertor. EmbeddedICE protocol convertor converts the
Remote Debug Protocol commands to the JTAG data needed to access the ARM
core.
相關PDF資料 |
PDF描述 |
|---|---|
| LPC2470 | Flashless 16-bit/32-bit micro; Ethernet, CAN, LCD, USB 2.0 device/host/OTG, external memory interface |
| LPD200P70 | PACKAGED HIGH DYNAMIC RANGE PHEMT |
| LPD200 | HIGH PERFORMANCE PHEMT |
| LPD200MX | HIGH PERFORMANCE PHEMT |
| LPD200SOT343 | DIODE DUAL 1600V 2X43A TO-247AD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC2294HBD144 | 制造商:NXP Semiconductors 功能描述:IC MCU 16/32BIT ARM7 144LQFP 制造商:NXP Semiconductors 功能描述:IC, MCU, 16/32BIT, ARM7, 144LQFP |
| LPC2294HBD144,551 | 功能描述:ARM微控制器 - MCU PREF PART LPC2294HBD144/01-S RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| LPC2294HBD144/00 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:16/32-bit ARM microcontrollers; 256 kB ISP/IAP flash with CAN, 10-bit ADC and external memory interface |
| LPC2294HBD144/01 | 制造商:NXP Semiconductors 功能描述:MCU, 16BIT/32BIT, 60MHZ, LQFP-144 制造商:NXP Semiconductors 功能描述:MCU, 16BIT/32BIT, 60MHZ, LQFP-144, Controller Family/Series:LPC2200, Core Size:1 制造商:NXP Semiconductors 功能描述:MCU, 16BIT/32BIT, 60MHZ, LQFP-144, Controller Family/Series:LPC2200, Core Size:16bit / 32bit, No. of I/O's:112, Supply Voltage Min:1.65V, Supply Voltage Max:1.95V, Digital IC Case Style:LQFP, No. of Pins:144, Program Memory |
| LPC2294HBD144/01,5 | 功能描述:ARM微控制器 - MCU ARM7 256KF/16KR/4CAN RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。