參數資料
型號： LPC2144FBD64
廠商： NXP Semiconductors N.V.
元件分類： 數學處理器
英文描述： Single-chip 16-bit-32-bit microcontrollers; up to 512 kB flash with ISP-IAP, USB 2.0 full-speed device, 10-bit ADC and DAC
封裝： LPC2141FBD64<SOT314-2 (LQFP64)|<<http://www.nxp.com/packages/SOT314-2.html<1<Always Pb-free,;LPC2142FBD64<SOT314-2 (LQFP64)|<<http://www.nxp.com/packages/SOT314-2.html<
文件頁數： 15/45頁
文件大小： 391K
代理商： LPC2144FBD64
LPC2141_42_44_46_48
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 5 — 12 August 2011
15 of 45
NXP Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
6.5 Interrupt controller
The Vectored Interrupt Controller (VIC) accepts all of the interrupt request inputs and
categorizes them as Fast Interrupt reQuest (FIQ), vectored Interrupt ReQuest (IRQ), and
non-vectored IRQ as defined by programmable settings. The programmable assignment
scheme means that priorities of interrupts from the various peripherals can be dynamically
assigned and adjusted.
FIQ has the highest priority. If more than one request is assigned to FIQ, the VIC
combines the requests to produce the FIQ signal to the ARM processor. The fastest
possible FIQ latency is achieved when only one request is classified as FIQ, because then
the FIQ service routine does not need to branch into the interrupt service routine but can
run from the interrupt vector location. If more than one request is assigned to the FIQ
class, the FIQ service routine will read a word from the VIC that identifies which FIQ
source(s) is (are) requesting an interrupt.
Vectored IRQs have the middle priority. Sixteen of the interrupt requests can be assigned
to this category. Any of the interrupt requests can be assigned to any of the 16 vectored
IRQ slots, among which slot 0 has the highest priority and slot 15 has the lowest.
Non-vectored IRQs have the lowest priority.
The VIC combines the requests from all the vectored and non-vectored IRQs to produce
the IRQ signal to the ARM processor. The IRQ service routine can start by reading a
register from the VIC and jumping there. If any of the vectored IRQs are pending, the VIC
provides the address of the highest-priority requesting IRQs service routine, otherwise it
provides the address of a default routine that is shared by all the non-vectored IRQs. The
default routine can read another VIC register to see what IRQs are active.
6.5.1
Interrupt sources
Each peripheral device has one interrupt line connected to the Vectored Interrupt
Controller, but may have several internal interrupt flags. Individual interrupt flags may also
represent more than one interrupt source.
6.6 Pin connect block
The pin connect block allows selected pins of the microcontroller to have more than one
function. Configuration registers control the multiplexers to allow connection between the
pin and the on chip peripherals. Peripherals should be connected to the appropriate pins
prior to being activated, and prior to any related interrupt(s) being enabled. Activity of any
enabled peripheral function that is not mapped to a related pin should be considered
undefined.
The Pin Control Module with its pin select registers defines the functionality of the
microcontroller in a given hardware environment.
After reset all pins of Port 0 and Port 1 are configured as input with the following
exceptions: If debug is enabled, the JTAG pins will assume their JTAG functionality; if
trace is enabled, the Trace pins will assume their trace functionality. The pins associated
with the I
2
C0 and I
2
C1 interface are open drain.
相關PDF資料
PDF描述
LPC2146FBD64 Single-chip 16-bit-32-bit microcontrollers; up to 512 kB flash with ISP-IAP, USB 2.0 full-speed device, 10-bit ADC and DAC
LPC2148FBD64 Single-chip 16-bit-32-bit microcontrollers; up to 512 kB flash with ISP-IAP, USB 2.0 full-speed device, 10-bit ADC and DAC
LPC2157FBD100 Single-chip 16-bit-32-bit microcontrollers; 512 kB flash, with 32 segment x 4 LCD driver
LPC2158FBD100 Single-chip 16-bit-32-bit microcontrollers; 512 kB flash, with 32 segment x 4 LCD driver
LPC2194HBD64 Single-chip 16-32-bit microcontroller; 256 kB ISP-IAP flash with 10-bit ADC and CAN
相關代理商/技術參數
參數描述
LPC2144FBD64,151 功能描述:ARM微控制器 - MCU ARM7 128KF/16KR/USB RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2144FBD64/S500, 制造商:NXP Semiconductors 功能描述:PHALPC2144FBD64/S500,151 16-BIT/32-BIT M
LPC2144FBD64151 制造商:NXP Semiconductors 功能描述:IC 32BIT MCU 60MHZ LQFP-64
LPC2144FBD64-S 制造商:NXP Semiconductors 功能描述:MCU 16-Bit/32-Bit LPC2000 ARM7TDMI-S RISC 128KB Flash 3.3V 64-Pin LQFP Tray
LPC2146 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:ARM7-based microcontrollers with full-speed USB 2.0
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*