- 您現在的位置：買賣IC網 > PDF目錄385495 > LP5526 (National Semiconductor Corporation) 4 Mbit Uniform Sector, Serial Flash Memory PDF資料下載
參數資料
| 型號： | LP5526 |
| 廠商： | National Semiconductor Corporation |
| 元件分類： | DRAM |
| 英文描述： | 4 Mbit Uniform Sector, Serial Flash Memory |
| 中文描述： | 4兆位統一部門，串行閃存 |
| 文件頁數： | 17/33頁 |
| 文件大?。?/td> | 1150K |
| 代理商： | LP5526 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
Functionality of Color LED
Outputs (RLED, GLED, BLED)
(Continued)
When RLED, GLED and BLED are connected together as in
Typical Application 1, flash current can be adjusted with
8.33% step in constant current mode by changing RGB max
current register values as seen on following table. Note that
0% means that appropriate output is turned off by setting
RSW, GSW or BSW bit to 0.
I
R
[%]
I
G
[%]
I
B
[%]
Total
current [%]
8.33
16.67
25.00
33.33
41.67
50.00
58.33
66.67
75.00
83.33
91.67
100
0
0
0
0
0
0
0
0
25
50
75
100
0
0
0
0
25
50
75
100
100
100
100
100
25
50
75
100
100
100
100
100
100
100
100
100
3. Using Flash Mode
In this mode Flash is triggered with external PWM pin and
pre-flash brightness is adjusted by adjusting the RGB max
current values. After flash pulse flash led will be shut down.
Write the pre-flash current values to RGB max current
register
Enable RGB functions and disable PWM mode (EN-
_RGB = 1, RGB_PWM = 0)
Enable flash mode (EN_FLASH = 1), make sure
GPIO[0]/PWM pin is in low state
Enable external PWM pin (EN_PWM_PIN = 1)
Start pre-flash by switching on the LEDs (RSW = 1, GSW
= 1, BSW = 1). Pre-flash brightness can be affected also
by setting on only one or two LEDs
Use EN_EXT_R_PWM, EN_EXT_G_PWM and EN-
_EXT_B_PWM bits to select which LED outputs are used
for flash
Start flash pulse by setting GPIO[0]/PWM pin high and
stop it by setting GPIO[0]/PWM pin low
During the flash pulse the LED outputs with EN_EXT_x-
_PWM bit enabled give out maximum current, regardless
of RGB max current register value or XSW values
Note: EN_FLASH bit must be set low, and then high again
before it is possible to make a new flash pulse.
20179704
Using Flash Mode
L
www.national.com
17
相關PDF資料 |
PDF描述 |
|---|---|
| LP5526TL | 4 Mbit Uniform Sector, Serial Flash Memory |
| LP5526TLX | 4 Mbit Uniform Sector, Serial Flash Memory |
| LP5550 | PowerWise Technology Compliant Energy Management Unit |
| LP5550SQ | PowerWise Technology Compliant Energy Management Unit |
| LP5550SQX | PowerWise Technology Compliant Energy Management Unit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LP5526TL | 制造商:Texas Instruments 功能描述:DRIVER FLASH LED 0.15A POWERWISE 制造商:Texas Instruments 功能描述:DRIVER FLASH LED 0.15A, POWERWISE |
| LP5526TL/NOPB | 功能描述:LED照明驅動器 RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| LP5526TLEV | 功能描述:電源管理IC開發工具 LP5526TL EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LP5526TLX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Lighting Management Unit with High Voltage Boost Converter with up to 150mA Serial FLASH LED Driver |
| LP5526TLX/NOPB | 功能描述:LED照明驅動器 RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
發布緊急采購，3分鐘左右您將得到回復。