- 您現在的位置：買賣IC網 > PDF目錄384605 > LMX9830SMX (NATIONAL SEMICONDUCTOR CORP) BluetoothTM Serial Port Module PDF資料下載
參數資料
| 型號： | LMX9830SMX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 通信及網絡 |
| 英文描述： | BluetoothTM Serial Port Module |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PBGA60 |
| 封裝： | 9 X 6 MM, 1.20 MM HEIGHT, 0.80 MM PITCH, PLASTIC, FBGA-60 |
| 文件頁數： | 19/46頁 |
| 文件大?。?/td> | 664K |
| 代理商： | LMX9830SMX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
19
www.national.com
L
8.0 Functional Description
(Continued)
8.6.4 Configuring the LMX9830 through transport layer
As described in Section 8.5 "System Power Up" on page 15,
the LMX9830 will check during startup the Options Regis-
ters if an external PROM is available. If the information on
the PROM are incomplete or no PROM is installed the
LMX9830 will boot into the “initialization Mode”.
The mode is confirmed by the “Await Initialization” Event.
The following information are needed to enter Bluetooth
Mode:
■
Bluetooth Device Address (BD_Addr)
■
External clock source (only if 10 - 20 MHz has been
selected)
■
UART Baudrate (only if Auto baudrate detection has
been selected)
In general the following procedure will initialize the
LMX9830:
1. Wait for “Await initialization” Event
- Event will only appear if transport layer speed is set or
after successful baudrate detection.
2. Send “Set Clock and Baudrate” Command only if the
clock speed is not known through hardware configura-
tion
(i.e only if OP3 OP4 OP5 = 0 1 0)
.
3. Send “Write BD_Addr” to Configure Local Bluetooth De-
vice Address.
4. Send “Enter Bluetooth Mode”
- LMX9830 will use configured clock and UART speed
and start the command interface.
NOTE: In case no EEPROM is used, BDAddr, clock source
and Baudrate are only valid until the next power-cycle or
hardware reset.
8.6.5 Auto Baud Rate Detection
The LMX9830 supports an Automatic Baudrate Detection in
case the external clock is different to 12, 13MHz or the
range 10-20 MHz or the baudrate is different to 9.6 kbps,
115.2 or 921.6kbit/s.
The baudrate detection is based on the measurement of a
single character. The following issues need to be consid-
ered:
■
The flow control pin CTS must be low or else the host is
in flow stop.
■
The Auto Baudrate Detector measures the length of the
0x01 character from the positive edge of bit 0 to the
positive edge of stop bit.
■
Therefore the very first received character must always
be a
0x01
.
■
The host can restrict itself to send only a 0x01 character
or also can send a command.
■
The host must flush the TX buffer within 50-100 millisec-
onds depend on clock frequency on the host controller.
■
After 50-100 milliseconds the UART is about to be initial-
ized and short after the host should receive a “Await
Initialization” Event or an “Command Status” Event.
Table 18. Fixed Frequencies
Osc Freq.
(MHz)
BBCLK
(MHz)
PLL
(48 MHz)
OP3
1
OP4
2
OP5
3
Function
12
12
OFF
0
0
0
UART speed read from NVS
10-20
4
10-20
1
ON
0
1
0
Clock and UART baudrate detection
13
13
OFF
1
0
0
UART speed read from NVS
13
13
OFF
1
0
1
UART speed 9.6 kbps
13
13
OFF
1
1
0
UART speed 115.2 kbps
13
13
OFF
1
1
1
UART speed 921.6 kbps
1.
2.
3.
4.
If OP3 is 1, must use 1k ohm pull up.
If OP4 is 1, must use 1k ohm pull up.
If OP5 is 1, must use 1k ohm pull up.
Supported frequencies see Table 22 on page 24
Figure 11. Auto baudrate detection timing diagram
CTS
RX
0x01
0x00
50 - 100ms delay
相關PDF資料 |
PDF描述 |
|---|---|
| LMX9838 | Bluetooth Serial Port Module |
| LMX9838SB | Bluetooth Serial Port Module |
| LMX9838SBX | Bluetooth Serial Port Module |
| LNBEH21 | LNB SUPPLY AND CONTROL IC WITH STEP-UP CONVERTER AND IC INTERFACE |
| LNBEH21PD | LNB SUPPLY AND CONTROL IC WITH STEP-UP CONVERTER AND IC INTERFACE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMX9830SMX/NOPB | 功能描述:射頻收發器 RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| LMX9838 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Bluetooth㈢ Serial Port Module |
| LMX9838_0709 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Bluetooth㈢ Serial Port Module |
| LMX9838DONGLE | 功能描述:藍牙/802.15.1 模塊 RoHS:否 制造商:Murata Wireless Solutions 類:1 頻帶:2402 MHz to 2480 MHz 靈敏度:- 92 dBm 數據速率: 工作電源電壓:2.2 V to 3.3 V 輸出功率: 接口類型:PCM, UART 天線連接器類型:Chip 最大工作溫度:+ 85 C 尺寸:17.5 mm x 16 mm x 2 mm |
| LMX9838DONGLE/NOPB | 功能描述:藍牙/802.15.1 模塊 RoHS:否 制造商:Murata Wireless Solutions 類:1 頻帶:2402 MHz to 2480 MHz 靈敏度:- 92 dBm 數據速率: 工作電源電壓:2.2 V to 3.3 V 輸出功率: 接口類型:PCM, UART 天線連接器類型:Chip 最大工作溫度:+ 85 C 尺寸:17.5 mm x 16 mm x 2 mm |
發布緊急采購，3分鐘左右您將得到回復。