參數資料
型號： LM9801CCV
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 模擬信號調理
英文描述： Greyscale/24-Bit Color Linear CCD Sensor Processor
中文描述： SPECIALTY ANALOG CIRCUIT, PQCC52
封裝： PLASTIC, LCC-52
文件頁數： 31/34頁
文件大?。?/td> 520K
代理商： LM9801CCV
Applications Information
(Continued)
Suggested timing for CIS devices is:
Mode
e
0 (Standard Mode)
*
RS Pulse Width
e
0 (2 MCLKs)
RS Pulse Polarity
e
0 (or 1 if circuit of Figure 21 is
used)
*
RS Pulse Position
e
0
Sample Reference Position
e
2
Sample Signal Position
e
14
w
1/
w
2/RS/TR Enable
e
0/0/1/1
TR Pulse Width
e
0
TR-
w
1 Guardband
e
0
TR Polarity
e
1
*
Signal Polarity
e
0
Dummy Pixels
e
2
Optical Black Pixels
e
10
(
*
Value given in CCD datasheet)
As CIS sensors approach pixel rates of 1 MHz and above
(corresponding to MCLK frequencies of 8 MHz and above),
the voltage during the reset level becomes less stable, mak-
ing it difficult to perform CDS on the output(Figure 22). The
solution is to create the ground reference externally, short-
ing the LM9801’s input to ground for half of the time using
the
w
1 clock, as shown in Figure 23.
TL/H/12814–49
FIGURE 22. High Speed CIS Waveforms
TL/H/12814–50
FIGURE 23. High Speed CIS Interface
10.0 HINTS AND COMMON SYSTEM DESIGN
PROBLEMS
10.1 Reading and Writing to the Configuration Register
The Configuration Register sends and receives data LSB
(Least Significant Byte) first. Some microcontrollers send
out data MSB (Most Significant Byte) first. The order of the
bits must be reversed to when using these microcontrollers.
Note:
Unlike the LM9800, the SYNC pin does not have to be held high to
send or receive data to or from the Configuration Register.
10.2 Setting the Dummy and Optical Black Pixel
Registers
The minimum value in the Dummy Pixels register is 2 (a
value of 0 or 1 will cause errors in the EOC and CCLK tim-
ing). Note that the value in this register should be equal to 1
plus the actual number of dummy pixels in the CCD. For
example, if the CCD being used with the LM9801 has 12
dummy pixels, this register should be set to 13. The mini-
mum number in the Optical Black Pixels register is 1.
10.3 Stretching the TR-
w
1 Guardband
Some CCDs (Sony’s ILX514, ILX518, and ILX524, for exam-
ple) require a TR to
w
1 guardband greater than the 100 ns
(2 MCLKs) provided by the LM9801. The circuit shown in
Figure 24 produces a 1
m
s
w
ROG (transfer) pulse with a
guardband between the end of the
w
ROG pulse and the
next edge of
w
1. This is done by setting the LM9801’s TR
pulse width register to 2
m
s and using the 74HC4538 to
generate a 1
m
s pulse inside that TR period to send to the
CCD.
TL/H/12814–51
FIGURE 24. Stretching the TR-
w
1 Guardband
http://www.national.com
31
相關PDF資料
PDF描述
LM9801CCVF Greyscale/24-Bit Color Linear CCD Sensor Processor
LM9822CCWMX2 RECTIFIER SCHOTTKY SINGLE 10A 25V 200A-Ifsm 0.45Vf 1A-IR D2PAK 50/TUBE
LM9822 LM9822 3 Channel 42-Bit Color Scanner Analog Front End
LM9822CCWM1 LM9822 3 Channel 42-Bit Color Scanner Analog Front End
LM9830VJD EuroDOCSIS 2.0 Diplexer Filter w/surge protection
相關代理商/技術參數
參數描述
LM9801CCVF 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Greyscale/24-Bit Color Linear CCD Sensor Processor
LM980-SC3 功能描述:基本/快動開關 Foot Switch RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel
LM9810 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM9810/20 10/12-Bit Image Sensor Processor Analog Front End
LM9810 WAF 制造商:Texas Instruments 功能描述:
LM9810CCWM 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM9810/20 10/12-Bit Image Sensor Processor Analog Front End
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*