參數資料
型號： LM8400
廠商： National Semiconductor Corporation
英文描述： Four Wire Resistive Touchscreen Controller with Brownout
中文描述： 四線電阻式觸摸屏控制器掉電
文件頁數： 18/20頁
文件大?。?/td> 319K
代理商： LM8400
9.0 Calibration
(Continued)
9.2 Calibration Procedures with Coordinates Checking
Enabled
To do TS calibration with coordinates checking enabled, first
ensure the Calibration Coordinates Checking is enabled on
the device. This can be accomplished by sending a com-
mand byte of $B1 (Read Parameters command) and check-
ing the 5th bit of the 12th reply byte is set. Alternatively, if the
device is set to Calibration Coordinates Checking enabled
as default, this step can be skipped.
The TS driver sends the command byte to do calibration
($BD). The TS driver should wait for the reply bytes and
ensure it is the same command bytes it sent. The device
waits for a touch to be detected on the panel. Once a touch
is detected, the device checks it against the predetermined
calibration values as noted on
Table 4
,
Table 5
, and
Table 6
.
If the detected touch is within the predefined value (
±
127 of
the raw A/D value), the device will send a command of $C4
to the TS driver and store the calibration point in the internal
flash. The TS driver can now send a command byte to do the
next calibration point. If the detected touch is not within the
predefined value, the device will send a reply byte of $C8 to
the TS driver. Upon receiving this reply byte, the TS driver
can resend the calibration command for the same calibration
point, go the next calibration point, or abort the calibration
process.
Once all the calibration points are done, the device does a
self-test. If the self-test was not successful, the device will
send a reply byte of $CC to the TS driver. At this point, the
TS driver should either notify the user to redo the calibration
point or automatically redo the calibration again. If the self-
test was successful, the device will send a reply byte of $CB
to the TS driver.
9.3 Calibration Procedures with Coordinates Checking
Disabled
To do TS calibration with coordinates checking disabled, first
ensure the Calibration Coordinates Checking is disabled on
the device. This can be accomplished by sending a com-
mand byte of $B1 (Read Parameters command) and check-
ing the 5th bit of the 12th reply byte is not set. Alternatively,
if the device is set to Calibration Coordinates Checking
disabled as default, this step can be skipped.
The TS driver sends the command byte to do calibration
($BD). The TS driver should wait for the reply bytes and
ensure it is the same command bytes it sent. The device
waits for a touch to be detected on the panel. Once a touch
is detected, the device save the values into the internal flash
and send a reply byte of $C4 to the TS driver. The TS driver
can now send a command byte to do the next calibration
point. Since the Calibration Checking is disabled, the TS
driver should ensure the calibration point is within the range
of the calibration cross.
Once all the calibration points are done, the device does a
self-test. If the self-test was not successful, the device will
send a reply byte of $CC to the TS driver. At this point, the
TS driver should either notify the user to redo the calibration
point or automatically redo the calibration again. If the self-
test was successful, the device will send a reply byte of $CB
to the TS driver.
L
www.national.com
18
相關PDF資料
PDF描述
LM8500 Four Wire Resistive Touchscreen Controller with Brownout
LM8500HLQ9 Four Wire Resistive Touchscreen Controller with Brownout
LM8500HMT9 Four Wire Resistive Touchscreen Controller with Brownout
LM8500HVA9 Four Wire Resistive Touchscreen Controller with Brownout
LM8500ILQ9 Four Wire Resistive Touchscreen Controller with Brownout
相關代理商/技術參數
參數描述
LM8460 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:ALARM CLOCK (CLOCK RADIO.ETC)
LM8471 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
LM84B WAF 制造商:Texas Instruments 功能描述:
LM84BIMQA 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
LM84BIMQA 制造商:Texas Instruments 功能描述:DIG TEMP SENSOR QSOP16-16 3.6V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*