- 您現在的位置：買賣IC網 > PDF目錄385489 > LM8400 (National Semiconductor Corporation) Four Wire Resistive Touchscreen Controller with Brownout PDF資料下載
參數資料
| 型號： | LM8400 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Four Wire Resistive Touchscreen Controller with Brownout |
| 中文描述： | 四線電阻式觸摸屏控制器掉電 |
| 文件頁數： | 17/20頁 |
| 文件大?。?/td> | 319K |
| 代理商： | LM8400 |
9.0 Calibration
(Continued)
9.1 General Calibration Procedures
Calibration is invoked by sending a command byte of $BD
followed by a command byte to the device. The command
byte is broken into two parts: the high nibble states the
number of calibration points to performs and the lower nibble
states the active calibration point. For example, to do the first
calibration point for the two point calibration, the command
bytes of $BD and $11 are sent to the device. The device then
echos $BD and $11 back to the TS driver and waits for a
touch on the panel. When a touch is detected, the device
checks to see if the point is within the specified parameters
if the calibration point checking is enabled. If the calibration
point checking is disabled, the device will send a
$
C8 for OK
byte to the TS driver regardless of where the touch was
detected. This calibration point checking can be enabled or
disabled by sending a command byte of $A5 to the device.
When all the calibration points are done, the device will do a
self-test and send a command of $CB for OK or a command
of $CC for failed. If a $CC is received, the TS driver should
issue a warning stating the calibration was not done properly
and redo the calibration procedures. The flowchart for the
calibration procedures is shown in
Figure 8
.
20037210
FIGURE 8. Calibration Procedures with Coordinates Checking Enabled
L
www.national.com
17
相關PDF資料 |
PDF描述 |
|---|---|
| LM8500 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM8500HLQ9 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM8500HMT9 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM8500HVA9 | Four Wire Resistive Touchscreen Controller with Brownout |
| LM8500ILQ9 | Four Wire Resistive Touchscreen Controller with Brownout |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM8460 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:ALARM CLOCK (CLOCK RADIO.ETC) |
| LM8471 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LM84B WAF | 制造商:Texas Instruments 功能描述: |
| LM84BIMQA | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM84BIMQA | 制造商:Texas Instruments 功能描述:DIG TEMP SENSOR QSOP16-16 3.6V |
發布緊急采購，3分鐘左右您將得到回復。