參數資料
型號: LM83CIMQA
廠商: NATIONAL SEMICONDUCTOR CORP
元件分類: 溫度/濕度傳感器
英文描述: LM 220P QWERTZ GERM/AUS/SWIT; Battery size code:6x AA RoHS Compliant: Yes
中文描述: DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT
封裝: QSOP-16
文件頁數: 8/20頁
文件大小: 331K
代理商: LM83CIMQA
Logic Electrical Characteristics
(Continued)
Note 6:
Typicals are at T
A
= 25C and represent most likely parametric norm.
Note 7:
Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 8:
The Temperature Error will vary less than
±
1.0 C for a variation in V
CC
of 3 V to 3.6 V from the nominal of 3.3 V.
Note 9:
Quiescent current will not increase substantially with an active SMBus.
Note 10:
This specification is provided only to indicate how often temperature data is updated. The LM83 can be read at any time without regard to conversion state
(and will yield last conversion result).
Note 11:
Default values set at power up.
Note 12:
Holding the SMBData and/or SMBCLK lines Low for a time interval greater than t
TIMEOUT
will cause the LM83 to reset SMBData and SMBCLK to the IDLE
state of an SMBus communication (SMBCLK and SMBData set High).
1.0 Functional Description
The LM83 temperature sensor incorporates a band-gap type
temperature sensor using a Local or three Remote diodes
and an 8-bit ADC (Delta-Sigma Analog-to-Digital Converter).
The LM83 is compatible with the serial SMBus and I
2
C two
wire interfaces. Digital comparators compare Local (LT) and
Remote (D1RT, D2RT and D3RT) temperature readings to
user-programmable
setpoints
D3RHS and TCS). Activation of the INT output indicates that
a comparison is greater than the limit preset in a HIGH reg-
ister. The T_CRIT setpoint (TCS) interacts with all the tem-
perature readings. Activation of the T_CRIT_A output indi-
cates that any or all of the temperature readings have
exceed the T_CRIT setpoint.
(LHS,
D1RHS,
D2RHS,
1.1 CONVERSION SEQUENCE
The LM83 converts its own temperature as well as 3 remote
diode temperatures in the following sequence:
1.
Local Temperature (LT)
1.
2.
3.
This round robin sequence takes approximately 480 ms to
complete as each temperature is digitized in approximately
120 ms.
Remote Diode 2 (D2RT)
Remote Diode 1 (D1RT)
Remote Diode 3 (D3RT)
1.2 INT OUTPUT and T_HIGH LIMITS
Each temperature reading (LT, D1RT, D2RT, and D3RT) is
associated with a T_HIGH setpoint register (LHS, D1RHS,
D2RHS, D3RHS).At the end of a temperature reading a digi-
tal comparison determines whether that reading has exceed
its HIGH setpoint. If the temperature reading is greater than
the HIGH setpoint, a bit is set in one of the Status Registers,
to indicate which temperature reading, and the INT output is
activated.
Local and remote temperature diodes are sampled in se-
quence by the A/D converter. The INT output and the Status
DS101058-5
FIGURE 2. Temperature-to-Digital Transfer Function (Non-linear scale for clarity)
DS101058-24
FIGURE 3. Printed Circuit Board Used for Thermal Resistance Specifications
L
www.national.com
8
相關PDF資料
PDF描述
LM83CIMQAX Triple-Diode Input and Local Digital Temperature Sensor with Two-Wire Interface
LM8560B Digital Alarm Clock(用于驅動LED顯示設備的數字鬧鐘)
LM8562 Digital Alarm Clock(用于驅動LED顯示設備的數字鬧鐘)
LM8569 Digital Alarm Clock(數字鬧鐘)
LM87 Serial Interface System Hardware Monitor with Remote Diode Temperature Sensing
相關代理商/技術參數
參數描述
LM83CIMQA 制造商:Texas Instruments 功能描述:IC TRIPLE DIODE TEMP SENSOR SMD
LM83CIMQA/NOPB 功能描述:板上安裝溫度傳感器 Triple Remote Diode Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
LM83CIMQA/NOPB 制造商:Texas Instruments 功能描述:DIGITAL TEMP SENSOR, 3 ~3.6V, 16QSOP
LM83CIMQA/NOPB 制造商:Texas Instruments 功能描述:Temperature Sensor IC
LM83CIMQAX 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor