- 您現在的位置：買賣IC網 > PDF目錄358877 > LM83CIMQA (NATIONAL SEMICONDUCTOR CORP) LM 220P QWERTZ GERM/AUS/SWIT; Battery size code:6x AA RoHS Compliant: Yes PDF資料下載
參數資料
| 型號： | LM83CIMQA |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | LM 220P QWERTZ GERM/AUS/SWIT; Battery size code:6x AA RoHS Compliant: Yes |
| 中文描述： | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | QSOP-16 |
| 文件頁數： | 18/20頁 |
| 文件大?。?/td> | 331K |
| 代理商： | LM83CIMQA |
4.0 Application Hints
(Continued)
6.
Avoid running diode traces close to or parallel to high
speed digital and bus lines. Diode traces should be kept
at least 2cm. apart from the high speed digital traces.
If it is necessary to cross high speed digital traces, the
diode traces and the high speed digital traces should
cross at a 90 degree angle.
The ideal place to connect the LM83’s GND pin is as
close as possible to the Processors GND associated
with the sense diode. For the Pentium II this would be
pin A14.
Leakage current between D+ and GND should be kept
to a minimum. One nano-ampere of leakage can cause
as much as 1C of error in the diode temperature read-
ing. Keeping the printed circuit board as clean as pos-
sible will minimize leakage current.
7.
8.
9.
Noise coupling into the digital lines greater than 300mVp-p
(typical hysteresis), overshoot greater than 500mV above
V
, and undershoot less than 500mV below GND, may pre-
vent successful SMBus communication with the LM83. SM-
Bus no acknowledge is the most common symptom, causing
unnecessary traffic on the bus. Although, the SMBus maxi-
mum frequency of communication is rather low (100kHz
max) care still needs to be taken to ensure proper termina-
tion within a system with multiple parts on the bus and long
printed circuit board traces. An R/C lowpass filter with a 3db
corner frequency of about 40MHz has been included on the
LM83’s SMBCLK input. Additional resistance can be added
in series with the SMBData and SMBCLK lines to further
help filter noise and ringing. Minimize noise coupling by
keeping digital traces out of switching power supply areas as
well as ensuring that digital lines containing high speed data
communications cross at right angles to the SMBData and
SMBCLK lines.
4.0 Typical Applications
DS101058-17
FIGURE 10. Ideal Diode Trace Layout
DS101058-22
FIGURE 11. LM83 Demo Board Diode Layout
L
www.national.com
18
相關PDF資料 |
PDF描述 |
|---|---|
| LM83CIMQAX | Triple-Diode Input and Local Digital Temperature Sensor with Two-Wire Interface |
| LM8560B | Digital Alarm Clock(用于驅動LED顯示設備的數字鬧鐘) |
| LM8562 | Digital Alarm Clock(用于驅動LED顯示設備的數字鬧鐘) |
| LM8569 | Digital Alarm Clock(數字鬧鐘) |
| LM87 | Serial Interface System Hardware Monitor with Remote Diode Temperature Sensing |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM83CIMQA | 制造商:Texas Instruments 功能描述:IC TRIPLE DIODE TEMP SENSOR SMD |
| LM83CIMQA/NOPB | 功能描述:板上安裝溫度傳感器 Triple Remote Diode Sensor RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM83CIMQA/NOPB | 制造商:Texas Instruments 功能描述:DIGITAL TEMP SENSOR, 3 ~3.6V, 16QSOP |
| LM83CIMQA/NOPB | 制造商:Texas Instruments 功能描述:Temperature Sensor IC |
| LM83CIMQAX | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。