- 您現在的位置：買賣IC網 > PDF目錄358871 > LM64CILQ-F (National Semiconductor Corporation) UART W/16BYTE TX/RX FIFO PDF資料下載
參數資料
| 型號： | LM64CILQ-F |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | UART W/16BYTE TX/RX FIFO |
| 中文描述： | 【1ΣC遠程二極管溫度傳感器，PWM風扇控制和5個GPIO的 |
| 文件頁數： | 14/29頁 |
| 文件大小： | 376K |
| 代理商： | LM64CILQ-F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
1.0 Functional Description
(Continued)
1.10 FAULT QUEUE
The LM64 incorporates a Fault Queue to suppress errone-
ous ALERT triggering . The Fault Queue prevents false
triggering by requiring three consecutive out-of-limit HIGH,
LOW, or T_CRIT temperature readings. See Figure 10. The
Fault Queue defaults to OFF upon power-up and may be
activated by setting the RDTS Fault Queue bit in the Con-
figuration Register to a 1.
1.11 ONE-SHOT REGISTER
The One-Shot Register is used to initiate a single conversion
and comparison cycle when the device is in standby mode,
after which the data returns to standby. This is not a data
register. A write operation causes the one-shot conversion.
The data written to this address is irrelevant and is not
stored. A zero will always be read from this register.
1.12 SERIAL INTERFACE RESET
In the event that the SMBus Master is reset while the LM64
is transmitting on the SMBDAT line, the LM64 must be
returned to a known state in the communication protocol.
This may be done in one of two ways:
1.
When SMBDAT is Low, the LM64 SMBus state machine
resets to the SMBus idle state if either SMBData or
SMBCLK are held Low for more than 35 ms (t
).
All devices are to timeout when either the SMBCLK or
SMBDAT lines are held Low for 25 ms – 35 ms. There-
fore, to insure a timeout of all devices on the bus, either
the SMBCLK or the SMBData line must be held Low for
at least 35 ms.
2.
With both SMBDAT and SMBCLK High, the master can
initiate an SMBus start condition with a High to Low
transition on the SMBDAT line. The LM64 will respond
properly to an SMBus start condition at any point during
the communication. After the start the LM64 will expect
an SMBus Address address byte.
20065513
FIGURE 10. Fault Queue Temperature Response
Diagram
L
www.national.com
14
相關PDF資料 |
PDF描述 |
|---|---|
| LM64K837 | Large Size Graphic Type LCD Module(大尺寸圖形LCD模塊) |
| LM64P12 | LIQUID CRYSTAL DISPLAY GROUP SHARP CORPOATION |
| LM64P832 | INTERFACE SPECIFICATION |
| LM64P83 | Large Size Graphic Type LCD Module(FA/POS/Measuring instruments) |
| LM64P89L | Large Size Graphic Type LCD Module(大尺寸圖形LCD模塊) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM64CILQ-F/NOPB | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM64CILQX-F | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM64CILQX-F/NOPB | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM64EVAL | 功能描述:溫度傳感器開發工具 LM64 EVAL BOARD RoHS:否 制造商:Texas Instruments 產品類型:Temperature Sensors and Control ICs 工具用于評估:MSP430G2553 接口類型:USB 工作電源電壓: 工作電源電流: |
| LM64K104 | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:Large Size Graphic Type LCD Module(FA/POS/Measuring instruments) |
發布緊急采購，3分鐘左右您將得到回復。