- 您現在的位置：買賣IC網 > PDF目錄358870 > LM5115SDX (NATIONAL SEMICONDUCTOR CORP) Secondary Side Post Regulator Controller PDF資料下載
參數資料
| 型號： | LM5115SDX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Secondary Side Post Regulator Controller |
| 中文描述： | 2.5 A SWITCHING CONTROLLER, PDSO16 |
| 封裝： | LLP-16 |
| 文件頁數： | 13/17頁 |
| 文件大?。?/td> | 725K |
| 代理商： | LM5115SDX |
Voltage Mode Control with Current Injection
(Continued)
Current Limiting (CS, CO and
VOUT)
Current limiting is implemented through the current sense
amplifier as illustrated in
Figure 6
. The current sense ampli-
fier monitors the inductor current that flows through a sense
resistor connected between CS and VOUT. The voltage gain
of the current sense amplifier is nominally equal to 16. The
output of current sense signal is shifted by 1.27V to produce
the internal CV reference signal. The CV signal drives a
current limit amplifier with nominal transconductance of
16mA/V. The current limit amplifier has an open drain (sink
only) output stage and its output pin CO is typically con-
nected to the COMP pin. During normal operation, the volt-
age error amplifier controls the COMP pin voltage which
adjusts the PWM duty cycle by varying the internal CRMIX
level (
Figure 4
). However, when the current sense input
voltage V
exceeds 45mV, the current limit amplifier pulls
down on COMP through the CO pin. Pulling COMP low
reduces the CRMIX signal below the CV signal level. When
CRMIX does not exceed the CV signal, the PWM compara-
tor inhibits output pulses until the CRMIX signal increases to
a normal operating level.
Acurrent limit fold-back feature is provided by the LM5115 to
reduce the peak output current delivered to a shorted load.
When the common mode input voltage to the current sense
amplifier (CS and VOUT pins) falls below 2V, the current limit
threshold is reduced from the normal level.At common mode
voltages
>
2V, the current limit threshold is nominally 45mV.
When VOUT is reduced to 0V the current limit threshold
drops to 36mV to reduce stress on the inductor and power
MOSFETs.
Negative Current Limit
When inductor current flows from the regulator output
through the low side MOSFET, the input to the current sense
comparator becomes negative. The intent of the negative
current comparator is to protect the low side MOSFET from
excessive currents. Negative current can lead to large nega-
tive voltage spikes on the output at turn off which can dam-
age circuitry powered by the output. The negative current
comparator threshold is sufficiently negative to allow induc-
tor current to reverse at no load or light load conditions. It is
not intended to support discontinuous conduction mode with
diode emulation by the low side MOSFET. The negative
current comparator shown illustrated in
Figure 6
monitors
the CV signal and compares this signal to a fixed 1V thresh-
old. This corresponds to a negative V
voltage between CS
and VOUT of -17mV. The negative current limit comparator
turns off the low side MOSFET for the remainder of the cycle
when the V
CL
input falls below this threshold.
Gate Drivers Outputs (HO & LO)
The LM5115 provides two gate driver outputs, the floating
high side gate driver HO and the synchronous rectifier low
side driver LO. The low side driver is powered directly by the
VCC regulator. The high side gate driver is powered from a
bootstrap capacitor connected between HB and HS. An
external diode connected between VCC and HB charges the
bootstrap capacitor when the HS is low. When the high side
MOSFET is turned on, HB rises with HS to a peak voltage
equal to VCC + V
- V
where V
is the forward drop of the
external bootstrap diode. Both output drivers have adaptive
dead-time control to avoid shoot through currents. The adap-
tive dead-time control circuit monitors the state of each
driver to ensure that the opposing MOSFET is turned off
before the other is turned on. The HB and VCC capacitors
should be placed close to the pins of the LM5115 to minimize
20134916
FIGURE 7. Voltage Sensing and Feedback
L
www.national.com
13
相關PDF資料 |
PDF描述 |
|---|---|
| LM5115MM | Secondary Side Post Regulator Controller |
| LM5115MMX | Secondary Side Post Regulator Controller |
| LM5152 | CABLE |
| LM5152BCN | Dual and Quad High Speed/Low Power 75 MHz GBW Rail-to-Rail I/O Operational Amplifiers |
| LM520A | WARM WHITE LAMP LED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM5115SDX/NOPB | 功能描述:開關變換器、穩壓器與控制器 RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| LM5116 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Wide Range Synchronous Buck Controller |
| LM5116-12EVAL | 功能描述:BOARD EVALUATION FOR LM5116-12 RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:PowerWise® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| LM5116-12EVAL/NOPB | 功能描述:電源管理IC開發工具 LM5116-12 EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LM5116BUCKEVM-BLDT | 功能描述:LM5116 WEBENCH? Buildit Board DC/DC, Step Down 1, Non-Isolated Outputs Evaluation Board 制造商:texas instruments 系列:WEBENCH? Buildit 板 零件狀態:有效 主要用途:DC/DC，步降 輸出和類型:1，非隔離 功率 - 輸出:- 電壓 - 輸出:- 電流 - 輸出:20A 電壓 - 輸入:7 V ~ 100 V 穩壓器拓?fù)?降壓 頻率 - 開關:- 板類型:裸（未填充） 所含物品:板 使用的 IC/零件:LM5116 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。