- 您現在的位置：買賣IC網 > PDF目錄358869 > LM5109MAX (NATIONAL SEMICONDUCTOR CORP) 100V / 1A Peak Half Bridge Gate Driver PDF資料下載
參數資料
| 型號： | LM5109MAX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 功率晶體管 |
| 英文描述： | 100V / 1A Peak Half Bridge Gate Driver |
| 中文描述： | 1 A HALF BRDG BASED MOSFET DRIVER, PDSO8 |
| 封裝： | MS-012AA, SOIC-8 |
| 文件頁數： | 7/9頁 |
| 文件大?。?/td> | 657K |
| 代理商： | LM5109MAX |
Timing Diagram
Layout Considerations
The optimum performance of high and low side gate drivers
cannot be achieved without taking due considerations during
circuit board layout. Following points are emphasized.
1.
A low ESR / ESL capacitor must be connected close to
the IC, and between V
DD
and V
SS
pins and between HB
and HS pins to support high peak currents being drawn
from VDD during turn-on of the external MOSFET.
2.
To prevent large voltage transients at the drain of the top
MOSFET, a low ESR electrolytic capacitor must be con-
nected between MOSFET drain and ground (V
SS
).
3.
In order to avoid large negative transients on the switch
node (HS) pin, the parasitic inductances in the source of
top MOSFET and in the drain of the bottom MOSFET
(synchronous rectifier) must be minimized.
4.
Grounding Considerations:
a) The first priority in designing grounding connections
is to confine the high peak currents from charging and
discharging the MOSFET gate in a minimal physical
area. This will decrease the loop inductance and mini-
mize noise issues on the gate terminal of the MOSFET.
The MOSFETs should be placed as close as possible to
the gate driver.
b) The second high current path includes the boot-
strap capacitor, the bootstrap diode, the local ground
referenced bypass capacitor and low side MOSFET
body diode. The bootstrap capacitor is recharged on the
cycle-by-cycle basis through the bootstrap diode from
the ground referenced V
bypass capacitor. The re-
charging occurs in a short time interval and involves high
peak current. Minimizing this loop length and area on the
circuit board is important to ensure reliable operation.
HS Transient Voltages Below
Ground
The HS node will always be clamped by the body diode of
the lower external FET. In some situations, board resis-
tances and inductances can cause the HS node to tran-
siently swing several volts below ground. The HS node can
swing below ground provided:
1.
HS must always be at a lower potential than HO. Pulling
HO more than -0.3V below HS can activate parasitic
transistors resulting in excessive current to flow from the
HB supply possibly resulting in damage to the IC. The
same relationship is true with LO and VSS. If necessary,
a Schottky diode can be placed externally between HO
and HS or LO and GND to protect the IC from this type
of transient. The diode must be placed as close to the IC
pins as possible in order to be effective.
2.
HB to HS operating voltage should be 15V or less .
Hence, if the HS pin transient voltage is -5V, VDD should
be ideally limited to 10V to keep HB to HS below 15V.
3.
A low ESR bypass capacitor between HB to HS as well
as VDD to VSS is essential for proper operation. The
capacitor should be located at the leads of the IC to
minimize series inductance. The peak currents from LO
and HO can be quite large. Any series inductances with
the bypass capacitor will cause voltage ringing at the
leads of the IC which must be avoided for reliable
operation.
20150518
FIGURE 3.
L
www.national.com
7
相關PDF資料 |
PDF描述 |
|---|---|
| LM5109 | 100V / 1A Peak Half Bridge Gate Driver |
| LM5110-2M | Dual 5A Compound Gate Driver with Negative Output Voltage Capability |
| LM5110-2MX | Dual 5A Compound Gate Driver with Negative Output Voltage Capability |
| LM5110-2SD | Dual 5A Compound Gate Driver with Negative Output Voltage Capability |
| LM5110-2SDX | Dual 5A Compound Gate Driver with Negative Output Voltage Capability |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM5109MAX/J7001236 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
| LM5109MAX/NOPB | 功能描述:功率驅動器IC RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| LM5109SD | 功能描述:IC DVR HALF-BRIDGE 100V 1A 8LLP RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:5 系列:- 配置:低端 輸入類型:非反相 延遲時間:600ns 電流 - 峰:12A 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:- 電源電壓:14.2 V ~ 15.8 V 工作溫度:-20°C ~ 60°C 安裝類型:通孔 封裝/外殼:21-SIP 模塊 供應商設備封裝:模塊 包裝:散裝 配用:BG2A-NF-ND - KIT DEV BOARD FOR IGBT 其它名稱:835-1063 |
| LM5109SD/NOPB | 功能描述:功率驅動器IC RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| LM5109SDX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:100V / 1A Peak Half Bridge Gate Driver |
發布緊急采購，3分鐘左右您將得到回復。