- 您現在的位置：買賣IC網 > PDF目錄358854 > LM3914VX LED Display Driver PDF資料下載
參數資料
| 型號： | LM3914VX |
| 元件分類： | 顯示驅動器 |
| 英文描述： | LED Display Driver |
| 中文描述： | LED顯示驅動器 |
| 文件頁數： | 5/12頁 |
| 文件大?。?/td> | 236K |
| 代理商： | LM3914VX |
Application Hints
GENERALIZED AUDIO POWER AMP DESIGN
Givens:
Power Output
Load Impedance
Input Sensitivity
Input Impedance
Bandwidth
The power output and load impedance determine the power
supply requirements. Output signal swing and current are
found from:
V
Opeak
e
0
2 R
L
P
O
(1)
I
Opeak
e
0
2 P
O
R
L
(2)
Add 5 volts to the peak output swing (V
OP
) for transistor
voltage to get the supplies, i.e.,
g
(V
OP
a
5V) at a current
of I
peak
. The regulation of the supply determines the unload-
ed voltage, usually about 15% higher. Supply voltage will
also rise 10% during high line conditions.
max supplies
&
g
(V
Opeak
a
5) (1
a
regulation) (1.1)
The input sensitivity and output power specs determine the
required gain.
A
V
t
P
O
R
L
V
IN
Normally the gain is set between 20 and 200; for a 25 watt,
8 ohm amplifier this results in a sensitivity of 710 mV and 71
mV, respectively. The higher the gain, the higher the THD,
as can be seen from the characteristics curves. Higher gain
also results in more hum and noise at the output.
(3)
e
V
ORMS
V
INRMS
(4)
The desired input impedance is set by R
IN
. Very high values
can cause board layout problems and DC offsets at the out-
put. The bandwidth requirements determine the size of C
f
and C
C
as indicated in the external component listing.
The output transistors and drivers must have a breakdown
voltage greater than the voltage determined by equation (3).
The current gain of the drive and output device must be high
enough to supply I
Opeak
with 5 mA of drive from the LM391.
The power transistors must be able to dissipate approxi-
mately 40% of the maximum output power; the drivers must
dissipate this amount divided by the current gain of the out-
puts. See the output transistor selection guide, Table A.
To prevent thermal runaway of the AB bias current the fol-
lowing equation must be valid:
i
JA
s
R
E
(
b
MIN
a
1)
V
CEQMAX
(K)
where:
(5)
i
JA
is the thermal resistance of the driver transistor, junc-
tion to ambient, in
§
C/W.
R
E
is the emitter degeneration resistance in ohms.
b
min
is that of the output transistor.
V
CEQMAX
is the highest possible value of one supply from
equation (3).
K is the temperature coefficient of the driver base-emitter
voltage, typically 2 mV/
§
C.
Often the value of R
E
is to be determined and equation (5)
is rearranged to be:
R
E
t
i
JA
(V
CEQMAX
) K
b
MIN
a
1
(6)
The maximum average power dissipation in each output
transistor is:
P
DMAX
e
0.4 P
OMAX
The power dissipation in the driver transistor is:
(7)
P
DRIVER(MAX)
e
P
DMAX
b
MIN
(8)
Heat sink requirements are found using the following formu-
las:
i
JA
s
T
JMAX
b
T
AMAX
P
D
(9)
(10)
i
SA
s
i
JA
b
i
JC
b
i
CS
where:
T
jMAX
is the maximum transistor junction temperature.
T
AMAX
is the maximum ambient temperature.
i
JA
is thermal resistance junction to ambient.
i
SA
is thermal resistance sink to ambient.
i
JC
is thermal resistance junction to case.
i
CS
is thermal resistance case to sink, typically 1
§
C/W for
most mountings.
5
相關PDF資料 |
PDF描述 |
|---|---|
| LM391 | LM391 Audio Power Driver |
| LM39301R-3.3 | 3A Low-Voltage Low-Dropout Regulator |
| LM393 | Dual Differential Comparators |
| LM193LB | Analog Comparator |
| LM2903DP | Low power dual voltage comparator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM3914VX/NOPB | 功能描述:LED照明驅動器 DOT/BAR DISPLAY DRVR RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| LM3915 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Dot/Bar Display Driver |
| LM3915J/A+ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LED Display Driver |
| LM3915N | 制造商:Texas Instruments 功能描述: 制造商:Texas Instruments 功能描述:IC LED DISPLAY DRIVER 3915 DIP18 |
| LM3915N/A+ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LED Display Driver |
發布緊急采購，3分鐘左右您將得到回復。