- 您現在的位置：買賣IC網 > PDF目錄385481 > LM359 (National Semiconductor Corporation) Dual, High Speed, Programmable, Current Mode Norton Amplifiers PDF資料下載
參數資料
| 型號： | LM359 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Dual, High Speed, Programmable, Current Mode Norton Amplifiers |
| 中文描述： | 雙路，高速，可編程，電流模式諾頓放大器 |
| 文件頁數： | 10/24頁 |
| 文件大小： | 742K |
| 代理商： | LM359 |
Application Hints
(Continued)
gain in the non-inverting configuration) some external fre-
quency compensation is required because the stray capaci-
tance to ground from the () input and the feedback resistor
add additional lagging phase within the feedback loop. The
value of the input capacitance will typically be in the range of
6 pF to 10 pF for a reasonably constructed circuit board.
When using a feedback resistance of 30 k
or less, the best
method of compensation, without sacrificing slew rate, is to
add a lead capacitor in parallel with the feedback resistor
with a value on the order of 1 pF to 5 pF as shown in Figure
10 .
Another method of compensation is to increase the effective
value of the internal compensation capacitor by adding ca-
pacitance from the COMP pin of an amplifier to ground. An
external 20 pF capacitor will generally compensate for all
gain settings but will also reduce the gain bandwidth product
and the slew rate. These same results can also be obtained
by reducing I
if the full capabilities of the amplifier are
not required. This method is termed over-compensation.
Another area of concern from a stability standpoint is that of
capacitive loading. The amplifier will generally drive capaci-
tive loads up to 100 pF without oscillation problems. Any
larger C loads can be isolated from the output as shown in
Figure 11 Over-compensation of the amplifier can also be
used if the corresponding reduction of the GBW product can
be afforded.
In most applications using the LM359, the input signal will be
AC coupled so as not to affect the DC biasing of the ampli-
fier. This gives rise to another subtlety of high frequency cir-
cuits which is the effective series inductance (ESL) of the
coupling capacitor which creates an increase in the imped-
ance of the capacitor at high frequencies and can cause an
unexpected gain reduction. Low ESL capacitors like solid
tantalum for large values of C and ceramic for smaller values
are recommended. A parallel combination of the two types is
even better for gain accuracy over a wide frequency range.
AMPLIFIER DESIGN EXAMPLES
The ability of the LM359 to provide gain at frequencies
higher than most monolithic amplifiers can provide makes it
most useful as a basic broadband amplification stage. The
design of standard inverting and non-inverting amplifiers,
though different than standard op amp design due to the cur-
rent differencing inputs, also entail subtle design differences
between the two types of amplifiers. These differences will
be best illustrated by design examples. For these examples
a practical video amplifier with a passband of 8 Hz to 10 MHz
and a gain of 20 dB will be used. It will be assumed that the
input will come from a 75
source and proper signal termi-
nation will be considered. The supply voltage is 12 V
and
single resistor programming of the operating current, I
SET
,
will be used for simplicity.
AN INVERTING VIDEO AMPLIFIER
1.
Basic circuit configuration:
2.
Determine the required I
from the characteristic
curves for gain bandwidth product.
GBW
= 10 x 10 MHz = 100 MHz
For a flat response to 10 MHz a closed loop response to two
octaves above 10 MHz (40 MHz) will be sufficient.
Actual GBW = 10 x 40 MHz = 400 MHz
I
SET
required = 0.5 mA
DS007788-15
C
f
= 1 pF to 5 pF for stability
FIGURE 10. Best Method of Compensation
DS007788-16
FIGURE 11. Isolating Large Capacitive Loads
DS007788-17
www.national.com
10
相關PDF資料 |
PDF描述 |
|---|---|
| LM359J | Dual, High Speed, Programmable, Current Mode Norton Amplifiers |
| LM359M | Dual, High Speed, Programmable, Current Mode Norton Amplifiers |
| LM359N | Dual, High Speed, Programmable, Current Mode Norton Amplifiers |
| LM3647IM | Universal Battery Charger for Li-Ion, Ni-MH and Ni-Cd Batteries |
| LM3647 | Universal Battery Charger for Li-Ion, Ni-MH and Ni-Cd Batteries |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM3590 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM3590Series White LED Driver |
| LM3590A E WAF | 制造商:Texas Instruments 功能描述: |
| LM3590MF | 制造商:Texas Instruments 功能描述:W LED DRIVER POWERWISE SOT-23-5 |
| LM3590MF/NOPB | 功能描述:IC LED DRIVER LINEAR SOT23-5 RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:PowerWise® 標準包裝:1 系列:- 恒定電流:- 恒定電壓:- 拓撲:PWM，切換式電容器（充電泵） 輸出數:1 內部驅動器:是 類型 - 主要:背光 類型 - 次要:白色 LED 頻率:642kHz 電源電壓:2.7 V ~ 5.5 V 輸出電壓:5V 安裝類型:表面貼裝 封裝/外殼:10-VFDFN 裸露焊盤 供應商設備封裝:10-VSON 包裝:剪切帶 (CT) 工作溫度:-30°C ~ 85°C 產品目錄頁面:1371 (CN2011-ZH PDF) 其它名稱:BD1603NUV-E2CT |
| LM3590MFEV | 功能描述:BOARD EVALUATION LM3590MF RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:PowerWise® 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
發布緊急采購，3分鐘左右您將得到回復。