- 您現在的位置：買賣IC網 > PDF目錄376111 > LM2576-12 (Motorola, Inc.) Easy Switcher 3.0A Step-Down Voltage Regulator PDF資料下載
參數資料
| 型號： | LM2576-12 |
| 廠商： | Motorola, Inc. |
| 英文描述： | Easy Switcher 3.0A Step-Down Voltage Regulator |
| 中文描述： | 輕松切換3.0A的降壓穩壓器 |
| 文件頁數： | 10/28頁 |
| 文件大?。?/td> | 301K |
| 代理商： | LM2576-12 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LM2576
10
MOTOROLA ANALOG IC DEVICE DATA
Procedure (Fixed Output Voltage Version)
In order to simplify the switching regulator design, a step–by–step
design procedure and some examples are provided.
Procedure
Example
Given Parameters:
Vout = Regulated Output Voltage (3.3 V, 5.0 V, 12 V or 15 V)
Vin(max) = Maximum Input Voltage
ILoad(max) = Maximum Load Current
Given Parameters:
Vout = 5.0 V
Vin(max) = 15 V
ILoad(max) = 3.0 A
1. Controller IC Selection
According to the required input voltage, output voltage and
current, select the appropriate type of the controller IC output
voltage version.
1. Controller IC Selection
According to the required input voltage, output voltage, current
polarity and current value, use the LM2576–5 controller IC
2. Input Capacitor Selection (Cin)
To prevent large voltage transients from appearing at the input
and for stable operation of the converter, an aluminium or
tantalum electrolytic bypass capacitor is needed between the
input pin +Vin and ground pin Gnd. This capacitor should be
located close to the IC using short leads. This capacitor should
have a low ESR (Equivalent Series Resistance) value.
2. Input Capacitor Selection (Cin)
A 100
μ
F, 25 V aluminium electrolytic capacitor located near to
the input and ground pins provides sufficient bypassing.
3. Catch Diode Selection (D1)
A.
Since the diode maximum peak current exceeds the
regulator maximum load current the catch diode current
rating must be at least 1.2 times greater than the maximum
load current. For a robust design the diode should have a
current rating equal to the maximum current limit of the
LM2576 to be able to withstand a continuous output short
B.
The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
3. Catch Diode Selection (D1)
A.
For this example the current rating of the diode is 3.0 A.
B.
Use a 20 V 1N5820 Schottky diode, or any of the suggested
fast recovery diodes shown in Table 1.
4. Inductor Selection (L1)
A.
According to the required working conditions, select the
correct inductor value using the selection guide from
Figures 18 to 22.
B.
From the appropriate inductor selection guide, identify the
inductance region intersected by the Maximum Input
Voltage line and the Maximum Load Current line. Each
region is identified by an inductance value and an inductor
code.
C.
Select an appropriate inductor from the several different
manufacturers part numbers listed in
Table 2.
The designer must realize that the inductor current rating
must be higher than the maximum peak current flowing
through the inductor. This maximum peak current can be
calculated as follows:
where ton is the “on” time of the power switch and
For additional information about the inductor, see the
inductor section in the “Application Hints” section of
this data sheet.
Ip(max)
ILoad(max)
Vin–Vout
ton
2L
ton
Vout
Vin
x1.0
fosc
4. Inductor Selection (L1)
A.
Use the inductor selection guide shown in Figures 19.
B.
From the selection guide, the inductance area intersected
by the 15 V line and 3.0 A line is L100.
C.
Inductor value required is 100
μ
H. From Table 2, choose
an inductor from any of the listed manufacturers.
相關PDF資料 |
PDF描述 |
|---|---|
| LM2576-15 | Easy Switcher 3.0A Step-Down Voltage Regulator |
| LM2576-3.3 | Easy Switcher 3.0A Step-Down Voltage Regulator |
| LM2576-5 | Easy Switcher 3.0A Step-Down Voltage Regulator |
| LM2576-ADJ | Easy Switcher 3.0A Step-Down Voltage Regulator |
| LM2904V | LinCMOS<TM> Precision Dual Operational Amplifier 8-PDIP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2576-12BT | 功能描述:IC REG BUCK 12V 3A TO220-5 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12 |
| LM2576-12BT⒂ | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:52kHz Simple 3A Buck Voltage Regulator |
| LM2576-12BU | 功能描述:IC REG BUCK 12V 3A TO263-5 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12 |
| LM2576-12BU TR | 功能描述:IC REG BUCK 12V 3A TO263-5 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12 |
| LM2576-12BUTR | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。