- 您現在的位置：買賣IC網 > PDF目錄43919 > LIS302DL (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PQCC14 PDF資料下載
參數資料
| 型號： | LIS302DL |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQCC14 |
| 封裝： | 3 X 5 MM, 0.92 MM HEIGHT, 0.80 MM PITCH, GREEN, PLASTIC, TLGA-14 |
| 文件頁數： | 14/42頁 |
| 文件大小： | 602K |
| 代理商： | LIS302DL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
LIS302DL
Digital interfaces
21/42
Figure 6.
Read & write protocol
CS is the Serial Port Enable and it is controlled by the SPI master. It goes low at the start of
the transmission and goes back high at the end. SPC is the Serial Port Clock and it is
controlled by the SPI master. It is stopped high when CS is high (no transmission). SDI and
SDO are respectively the Serial Port Data Input and Output. Those lines are driven at the
falling edge of SPC and should be captured at the rising edge of SPC.
Both the Read Register and Write Register commands are completed in 16 clock pulses or
in multiple of 8 in case of multiple byte read/write. Bit duration is the time between two falling
edges of SPC. The first bit (bit 0) starts at the first falling edge of SPC after the falling edge
of CS while the last bit (bit 15, bit 23, ...) starts at the last falling edge of SPC just before the
rising edge of CS.
bit 0: RW bit. When 0, the data DI(7:0) is written into the device. When 1, the data DO(7:0)
from the device is read. In latter case, the chip will drive SDO at the start of bit 8.
bit 1: MS bit. When 0, the address will remain unchanged in multiple read/write commands.
When 1, the address will be auto incremented in multiple read/write commands.
bit 2-7: address AD(5:0). This is the address field of the indexed register.
bit 8-15: data DI(7:0) (write mode). This is the data that will be written into the device (MSb
first).
bit 8-15: data DO(7:0) (read mode). This is the data that will be read from the device (MSb
first).
In multiple read/write commands further blocks of 8 clock periods will be added. When MS
bit is 0 the address used to read/write data remains the same for every block. When MS bit
is 1 the address used to read/write data is incremented at every block.
The function and the behavior of SDI and SDO remain unchanged.
CS
SPC
SDI
SDO
RW
AD5 AD4 AD3 AD2 AD1 AD0
DI7DI6 DI5DI4 DI3DI2 DI1DI0
DO7DO6 DO5DO4 DO3DO2 DO1DO0
MS
相關PDF資料 |
PDF描述 |
|---|---|
| LIS302DLTR8 | SPECIALTY ANALOG CIRCUIT, PQCC14 |
| LIS331ALTR | SPECIALTY ANALOG CIRCUIT, QCC16 |
| LIS331DLF | SPECIALTY ANALOG CIRCUIT, PBCC16 |
| LIS331DLHTR | SPECIALTY ANALOG CIRCUIT, PBCC16 |
| LIS331DLMTR | SPECIALTY ANALOG CIRCUIT, PBCC16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LIS302DL_07 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MEMS motion sensor 3-axis - 【2g/【8g smart digital output “piccolo” accelerometer |
| LIS302DL_08 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MEMS motion sensor 3-axis - ?± 2g/?± 8g smart digital output a??piccoloa?? accelerometer |
| LIS302DLH | 功能描述:加速計 - 板上安裝 3 AXIS DIGITAL MEMS ACCELEROMETER RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS302DLHTR | 功能描述:加速計 - 板上安裝 MEMS digital output L-Power Motion Snsr RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS302DLTR | 功能描述:加速計 - 板上安裝 MEMS Motion Sensor RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
發(fā)布緊急采購，3分鐘左右您將得到回復。