- 您現在的位置：買賣IC網 > PDF目錄358759 > LC72323R (Sanyo Electric Co.,Ltd.) Single-Chip Microcontroller with PLL and LCD Driver PDF資料下載
參數資料
| 型號： | LC72323R |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Single-Chip Microcontroller with PLL and LCD Driver |
| 中文描述： | 單片微控制器，帶有PLL和LCD驅動器 |
| 文件頁數： | 8/13頁 |
| 文件大小： | 205K |
| 代理商： | LC72323R |
Continued from preceding page.
No. 5378-8/13
LC72322R, 72323R
Continued on next page.
Pin
Pin No.
Functions
I/O
I/O circuit type
PH0
PH1
PH2/DAC
*
1
PH3/DAC
*
2
PI0/S25
PI1/S26
PI2/S27
PI3/S28
S1 to S24
COM1
COM2
FMIN
AMIN
55
56
57
58
26
27
28
29
2 to 25
80
1
71
70
Dedicated output ports
Since these pins are high-breakdown voltage n-channel
transistor open-drain outputs, they can be effectively used for
functions such as band power supply switching.
And, PH2 and PH3 can also be used for DAC1 and DAC2
output ports respectively. (
*
: DAC is contained in LC72322R
only.)
These ports go to the high impedance state during a reset,
i.e., when the RES pin is low, and in BACKUP mode.
Dedicated output ports
While these pins have a CMOS output circuit structure, they
can be switched to function as LCD drivers. Their function is
switched by the SS and RS instructions. These pins cannot
be switched individually.
The LCD driver function is selected and a segment-off signal
is output when power is first applied or when RES is low.
These pins are held at the low level in BACKUP mode.
Note that when the general-purpose port use option is
specified, these pins output the contents of IPORT when LPC
is 1, and the contents of the general-purpose output port
LATCH when LPC is 0.
LCD driver segment outputs
A frame frequency of 100 Hz and a 1/2 duty, 1/2 bias drive
type are used.
A segment-off signal is output when power is first applied or
when RES is low.
These pins are held at the low level in BACKUP mode.
The use of these pins as general-purpose output ports can be
specified as an option.
LCD driver common outputs
A 1/2 duty, 1/2 bias drive type is used.
The output when power is first applied or when RES is low is
identical to the normal operating mode output.
These pins are held at the low level in BACKUP mode.
FM VCO (local oscillator) input
The input must be capacitor coupled.
The input frequency range is from 10 to 130 MHz.
(Max. 150 MHz)
AM VCO (local oscillator) input
The input must be capacitor coupled
The band supported by this pin can be selected using the PLL
instruction.
High (2 to 40 MHz)
→
SW
Low (0.5 to 10 MHz)
→
LW and MW
Output
Output
Output
Output
Input
相關PDF資料 |
PDF描述 |
|---|---|
| LC7232N | CLAMP, CAPACITOR; Centres, fixing:57mm; Diameter, clip:40mm; Length / Height, external:14mm RoHS Compliant: Yes |
| LC723341E | RESISTOR-100 OHM,1/4W,5% |
| LC72336 | Single-Chip Microcontrollers with Built-In LCD Driver and PLL Circuits |
| LC7233N-8818 | Single-Chip PLL and Controller with LCD Driver(用于電子調諧的單片微控制器（帶LCD驅動器和鎖相環電路 ）) |
| LC7233N | Single-Chip PLL and Microcontroller with LCD Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC72323-XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LC72323-XXXX | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Provisional Development Specifications |
| LC7232-8291 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:1-Chip PLL + Controller |
| LC7232-8377 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-chip PLL and Microcontroller with LCD Driver |
| LC7232N | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-Chip PLL and Microcontroller with LCD Driver |
發布緊急采購，3分鐘左右您將得到回復。