- 您現在的位置：買賣IC網 > PDF目錄358757 > LC587008 (Sanyo Electric Co.,Ltd.) Single-Chip 4-Bit Microprocessors with LCD Driver,2 Kb RAM, and 16 KB ROM on chip(4位單片微控制器（帶LCD驅動器，16K位ROM和2K位RAM）) PDF資料下載
參數資料
| 型號： | LC587008 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Single-Chip 4-Bit Microprocessors with LCD Driver,2 Kb RAM, and 16 KB ROM on chip(4位單片微控制器（帶LCD驅動器，16K位ROM和2K位RAM）) |
| 中文描述： | 單芯片4位的LCD驅動器，2 Kb的RAM和16片KB光盤（4位單片微控制器（帶液晶顯示驅動器，16K的位光盤和2K位RAM）的微處理器） |
| 文件頁數： | 10/29頁 |
| 文件大?。?/td> | 519K |
| 代理商： | LC587008 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Crystal Oscillator Circuit Options
Input Port Options
No. 4435-10/29
LC587008, 587006, 587004
Option
Circuit configuration
Note
32 kHz oscillator
5 kHz oscillator
38 kHz oscillator
The resistor Rd (200 k
typical) for use with a
32 kHz oscillator is built in.
The cycle time is four times n times the f1
period. (Note: n is 2.)
The divider outputs (1 to 15) are used as
the time base, the LCD drive waveform
generation clock, the S and K port
chattering rejection clock and for other
functions.
OSC1 is stopped when a SLOW instruction
is executed.
Option
Circuit configuration
Note
Selection of either the
Built-in pull-up
resistor, or the
Built-in pull-down
resistor option
Selection of high or
low level hold
transistor
The following ports are switched at the same
time
S1 to S4, K1 to K4, M1 to M4, P1 to P4 SO1
to SO4 and A1 to A4
At reset: The resistors are on during the reset
period.
The resistors are turned off when
reset is cleared.
Options: Either A or B can be selected.
One of A and B must be selected.
When the hold transistors used option is
selected:
Used to reduce the current flowing in the
pull-up or pull-down resistors when, for
example, a push switch is used for S1 or a
slide switch is used for S2.
For input open specification versions, the
resistors are turned on before the input is
read, the input state is read and then the
resistors are turned off. If the input is
floating at this point the high or low level
hold transistor operates to hold the value
read.
When the hold transistors unused option is
selected:
Use with the pull-up or pull-down resistor in
the on state.
Select hold transistors unused when
connecting to external control signals and
the connections will never be floating
Combination examples
Type
1
2
3
4
Pull-up resistor (A)
On
On
Pull-down resistor (B)
On
On
High level hold transistor (C)
On
Low level hold transistor (D)
On
相關PDF資料 |
PDF描述 |
|---|---|
| LC587202A | Single-Chip 4-Bit Micontroller with LCD Driver,512 ×4bit RAM,2K× 16 Bit ROM on chip(單片4位微控制器（帶LCD驅動器，512 ×4位RAM和2K× 16位ROM）) |
| LC5872 | Single-Chip 4-Bit Microprocessors with LCD Driver,1 Kb RAM, and 4 KB ROM on chip(單片4位微控制器（帶LCD驅動器，1K位RAM和4K位ROM）) |
| LC587504A | LC587508A |
| LC58E68 | 4-Bit Microprocessor with Built-in EPROM and LCD Drivers |
| LC58E7008 | On-Chip EPROM Microcomputer 4-Bit Single-Chip Microcontroller with LCD Driver, 16 Kbytes of EPROM and 2Kbits of RAM On-Chip |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC5872 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:On-Chip EPROM Microcomputer 4-Bit Single-Chip Microprocessor with LCD Driver, 12 Kbytes of EPROM and 1Kbits of RAM On-Chip |
| LC587202A | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:4-Bit Single-Chip Microcontroller LCD Driver ROM:2,4,6,or8 K x 16 bits, RAM:512 x4 bits |
| LC587204A | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:4-Bit Single-Chip Microcontroller LCD Driver ROM:2,4,6,or8 K x 16 bits, RAM:512 x4 bits |
| LC587206A | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:4-Bit Single-Chip Microcontroller LCD Driver ROM:2,4,6,or8 K x 16 bits, RAM:512 x4 bits |
| LC587208A | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:4-Bit Single-Chip Microcontroller LCD Driver ROM:2,4,6,or8 K x 16 bits, RAM:512 x4 bits |
發布緊急采購，3分鐘左右您將得到回復。