- 您現在的位置：買賣IC網 > PDF目錄97996 > LB11691 BRUSHLESS DC MOTOR CONTROLLER, 0.05 A, PDIP36 PDF資料下載
參數資料
| 型號： | LB11691 |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 0.05 A, PDIP36 |
| 封裝： | 0.400 INCH, DIP-36 |
| 文件頁數： | 10/19頁 |
| 文件大?。?/td> | 204K |
| 代理商： | LB11691 |
TDF8546
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 3 — 30 August 2011
18 of 61
NXP Semiconductors
TDF8546
I2C-bus controlled 4
45 W best efficiency amplifier
information is seen at pin DIAG as a logical OR. In case of a failure, pin DIAG remains
LOW and the microcontroller can read the failure information via the I2C-bus; pin DIAG
can be used as a microcontroller interrupt to minimize I2C-bus traffic. When the failure is
removed, pin DIAG is released.
To enable full control over the clipping information, pin STB can be programmed as a
second-clip detection pin. The clip detection level can be selected for all channels at once.
The clip information can be selected to be available separately at pin DIAG or at pin STB
for each channel. It is possible, for example, to distinguish between clipping of the front
and the rear channels.
The diagnostic information available at either of the two diagnostic pins DIAG and STB is
shown in Table 4.
7.6.1 Start-up diagnostics with DC load detection
If the start-up diagnostics are enabled, the load condition of all four channels is
determined. At the end of the start-up diagnostics cycle, not only the load condition is
known (shorted load, normal load or open load), but also if a separate amplifier is
connected or if the outputs are shorted to battery or ground. If a separate amplifier
(booster) is detected, the amplifier can start-up in line driver mode (low gain setting).
Table 4.
Diagnostic information on pins DIAG and STB
Diagnostic
information
I2C-bus mode
Legacy mode
DIAG pin
STB pin
DIAG pin
Power-On Reset
(POR)
after POR, pin DIAG
remains LOW until
amplifier starts (inverse
of start-up bit)
no
Low battery
yes
no
yes
Clip detection
can be enabled per
channel; can be
enabled by IB1[D7] if
below VP =10V;
default is ‘blocked’
can be enabled per
channel; can be
enabled by IB1[D7] if
below VP =10 V;
default is ‘blocked’
yes; fixed level for all
channels at 2 %;
blocked for VP < 10 V
Temperature pre-
warning
can be enabled;
default: Tj(AV)(pwarn) =
160 C
no
yes, pre-warning level
is
Tj(AV)(pwarn) =
160 C
Short
can be enabled; default
is enabled
no
yes
Speaker fault detection no
no
Offset detection
no
Load detection
no
Overvoltage protection
(20 V)
yes
no
yes
Overvoltage
pre-warning (16 V)
can be enabled; default
is disabled
no
Maximum temperature
protection (active)
yes
no
yes
Start-up diagnostics
indication
no
相關PDF資料 |
PDF描述 |
|---|---|
| LB11693JH | BRUSHLESS DC MOTOR CONTROLLER, 1.8 A, PDSO36 |
| LB11695M | BRUSHLESS DC MOTOR CONTROLLER, 0.04 A, PDSO30 |
| LB11697V | BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO30 |
| LB11697V | BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO30 |
| LB11826 | BRUSHLESS DC MOTOR CONTROLLER, 2.5 A, DFM28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB11691H | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic digital IC Pre-Driver IC for Brushless Motor Drive in Electric Bicycles |
| LB11691H-TLM-E | 制造商:Sony Semiconductor Solutions Division 功能描述: |
| LB11692JH | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic Digital IC 24V Fan Motor Driver IC |
| LB11693 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Three-Phase Brushless Motor Driver for 24 V Fan Motors |
| LB11693H | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Monolithic Digital IC 3-Phase Brushless Motor Driver for 24V Fan Motors |
發布緊急采購，3分鐘左右您將得到回復。