- 您現在的位置：買賣IC網 > PDF目錄10367 > LA4425PV-TLM-H (ON Semiconductor)IC AUDIO POWER AMP 5W 44SSOP PDF資料下載
參數資料
| 型號： | LA4425PV-TLM-H |
| 廠商： | ON Semiconductor |
| 文件頁數： | 8/8頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AUDIO POWER AMP 5W 44SSOP |
| 標準包裝： | 2,000 |
| 類型： | AB 類 |
| 輸出類型： | 1-通道（單聲道） |
| 在某負載時最大輸出功率 x 通道數量： | 6W x 1 @ 4 歐姆 |
| 電源電壓： | 5 V ~ 16 V |
| 特點： | 消除爆音，過壓保護，短路保護，熱保護 |
| 安裝類型： | * |
| 供應商設備封裝： | * |
| 封裝/外殼： | * |
| 包裝： | * |
8
INDUSTRIAL TEMPERATURERANGE
IDT72V73250 3.3V TIME SLOT INTERCHANGE
DIGITAL SWITCH 8,192 x 8,192
TABLE 5 — CONTROL REGISTER (CR) BITS
Reset Value:
0000H.
BIT
NAME
DESCRIPTION
15
SRS
A one will reset the device and have the same effect as the RESET pin. Must be zero for normal operation.
(SoftwareReset)
14
OEI
When 1, the TX8-15/OEI0-7 pins will be OEI0-7 and reflect the active or high-impedance state of their corresponding output
(OutputEnableIndication)
data streams. When 0, this feature is disabled and these pins are used as output data streams TX8-15.
13
OEPOL
When1,aoneonanOutputEnableIndicationpindenotesanactivestateontheoutputdatastream;zeroonanOutputEnableIndication
(Output Enable Polarity)
pin denoteshigh-impedancestate.When0,aoneonanOutputEnableIndicationpindenoteshigh-impedanceandazerodenotes
and active state.
12
AOE
When 1, TX0-15 will behave as OEI0-15 accordingly. These outputs will reflect the active or high-impedance state of the
(All Output Enable)
corresponding output data streams (TX0-15) in another IDT72V73250 if programmed identically. When 0, the TSI operates in the
normal switch mode.
11-10
Unused
Must be zero for normal operation.
9
MBP
When 1, the Connection Memory block programming feature is ready for the programming of Connection Memory HIGH bits, bit
(Memory Block Program)
14 to bit 15. When 0, this feature is disabled.
8-7
BPD1-0
These bits carry the value to be loaded into the Connection Memory block whenever the memory block programming feature
(Block Programming
is activated. After the Memory Block Program bit in the Control Register is set to 1 and the Block Programming Enable is set to
Data)
1, the contents of the bits Block Programming Data1-0 are loaded into bit 15 and 14 of the Connection Memory. Bit 13 to bit 0 of
the Connection Memory are set to 0.
6
BPE
A zero to one transition of this bit enables the memory block programming function. The Block Programming Enable and
(Begin Block
BlockProgrammingData1-0bitsintheControlRegister havetobedefinedinthesamewriteoperation.OncetheBlockProgramming
ProgrammingEnable)
Enable bit is set HIGH, the device requires two frames to complete the block programming. After the programming function has
finished, the Block Programming Enable, Memory Block Program and Block Programming Data 1-0 bits will be reset to
zero by the device to indicate the operation is complete.
5
OSB
When ODE = 0 and Output Stand By = 0, the output drivers of the transmit serial streams are in high-impedance mode. When
(Output Stand By)
either ODE = 1 or Output Stand By =1, the output serial streams drivers function normally.
4
SFE
A zero to one transition in this bit starts the Frame Evaluation procedure. When the Complete Frame Evaluation bit in the Frame
(Start Frame Evaluation)
Alignment Register changes from zero to one, the evaluation procedure stops. To start another Frame Evaluation cycle, set this
bit to zero for at least one frame.
3-0
Unused
Must be zero for normal operation.
15
14
13
12
11
10
9876543210
SRS
OEI
OEPOL
AOE
0
MBP
BPD1
BPD0
BPE
OSB
SFE
0000
TABLE 6 — CONNECTION MEMORY BITS
15
14
13
12
11
10
9876543210
MOD1
MOD0
0
SAB3
SAB2
SAB1
SAB0
CAB8
CAB7
CAB6
CAB5
CAB4
CAB3
CAB2
CAB1
CAB0
Bit
Name
Description
15, 14
MOD1-0
MOD1
MOD0
MODE
(Switching Mode Selection)
0
Variable Delay mode
0
1
Constant Delay mode
1
0
Processor mode
1
OutputHigh-impedance
13
Unused
Must be zero for normal operation.
12-9
SAB3-0
The binary value is the number of the data stream for the source of the connection.
(Source Stream Address Bits)
8-0
CAB8-0
The binary value is the number of the channel for the source of the connection.
(Source Channel Address Bits)
相關PDF資料 |
PDF描述 |
|---|---|
| MS27472T10B99P | CONN RCPT 7POS WALL MT W/PINS |
| VI-2NX-IW-F4 | CONVERTER MOD DC/DC 5.2V 100W |
| MS27468T15F5P | CONN RCPT 5POS JAM NUT W/PINS |
| ISL54005IRTZ-T | IC AMP AUDIO PWR 1.23W AB 20TQFN |
| VI-2NW-IW-F2 | CONVERTER MOD DC/DC 5.5V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LA4430 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LA4440 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:6W 2-Channel, Bridge 19W typ Power Amplifier |
| LA4440-E | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LA4440J-K-E | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LA4445 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:5.5W 2-Channel AF Power Amplifier |
發布緊急采購，3分鐘左右您將得到回復。