- 您現在的位置：買賣IC網 > PDF目錄43901 > L9952GXP (STMICROELECTRONICS) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO36 PDF資料下載
參數資料
| 型號： | L9952GXP |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO36 |
| 封裝： | LEAD FREE, SSO-36 |
| 文件頁數： | 11/68頁 |
| 文件大?。?/td> | 859K |
| 代理商： | L9952GXP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
L9952GXP
Description
Doc ID 13518 Rev 5
2.10
Fail safe output
After power-on (Vs > VPOR) or wakeup from VBAT -standby mode, the output FSO is set to
“HIGH”, if V1 is above the V1 threshold. FSO is set to “LOW” in case of V1 under voltage or
watchdog failure.
During V1-standby mode, FSO is HIGH unless a V1 under-voltage or watchdog reset
occurs. WD remains enabled in V1 standby mode until IV1 drops below 150uA. In VBAT -
standby mode, FSO is low. At exit from VBAT - standby mode, it goes to high as soon as V1
is stable.
At wakeup FSO remains high, provided that the watchdog is triggered successfully. It is set
low if the watchdog is not served during the long open window of if a V1 under-voltage
occurs.
Figure 5.
FSO
2.11
Reset – generator
IF V1 is turned on and the voltage exceeds the V1 reset threshold, the reset output
“NRESET” is switched to “HIGH” after a 2ms reset delay time. This is necessary for a
defined start of the micro controller when the application is switched on.
As soon as an under voltage condition of the output voltage (V1 < VRT) for more than 8us
appears, the reset output is switched low again.
Figure 6.
NReset
FSO = 0
Vbatstdby Mode
V1 undervoltage
Watchdog Failure
TSD2
NReset = 0
V1 Undervoltage
Wake-up Event 1)
1) Only if
(INT_en = 0) and (wake-up by WU-input or High Side Open Load)
Vpwm2 < 9V
(Exit Flash Mode)
Watchdog
Failure
相關PDF資料 |
PDF描述 |
|---|---|
| L9952GXPTR | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO36 |
| L99H01QF | BRUSH DC MOTOR CONTROLLER, PQFP32 |
| L99H01XPTR | BRUSH DC MOTOR CONTROLLER, PDSO36 |
| L99PM62XP | 4-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO36 |
| LA5635H | SPECIALTY ANALOG CIRCUIT, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9952GXPTR | 功能描述:馬達/運動/點火控制器和驅動器 Power management system IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9952XP | 功能描述:馬達/運動/點火控制器和驅動器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9952XPTR | 功能描述:馬達/運動/點火控制器和驅動器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9953 | 功能描述:馬達/運動/點火控制器和驅動器 Door actuator DRVR RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L-995-38 | 制造商:MOLEX 制造商全稱:Molex Electronics Ltd. 功能描述:NylaKrimp? Funnel Entry Ring Tongue Terminal for 4/0 AWG Wire, Stud #9 |
發布緊急采購，3分鐘左右您將得到回復。