- 您現在的位置：買賣IC網 > PDF目錄43901 > L9951TR (STMICROELECTRONICS) BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36 PDF資料下載
參數資料
| 型號： | L9951TR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36 |
| 封裝： | ROHS COMPLIANT, SOP-36 |
| 文件頁數： | 34/36頁 |
| 文件大?。?/td> | 532K |
| 代理商： | L9951TR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁
L9951 / L9951XP
Block diagram and pin description
Doc ID 14173 Rev 8
7/36
Table 2.
Pin definitions and functions
Pin
Symbol
Function
1, 18, 19,
36
GND
Ground
.
Reference potential.
Note: For the capability of driving the full current at the outputs all pins of
GND must be externally connected.
6, 7, 14,
15, 23, 24,
29, 32
VS
Power supply voltage (external reverse protection required).
For EMI reason a ceramic capacitor as close as possible to GND is
recommended.
Note: for the capability of driving the full current at the outputs all pins of
VS must be externally connected.
3, 4, 34
OUT1
Half-bridge output 1.
The output is built by a high side and a low side switch, which are
internally connected. The output stage of both switches is a power
DMOS transistor. Each driver has an internal reverse diode (bulk-drain-
diode: high side driver from output to VS, low side driver from GND to
output). This output is over-current and open-load protected.
Note: for the capability of driving the full current at the outputs all pins of
OUT1 must be externally connected.
8DI
Serial data input.
The input requires CMOS logic levels and receives serial data from the
microcontroller. The data is a 16bit control word and the least significant
bit (LSB, bit 0) is transferred first.
9CM/PWM
Current monitor output/PWM input.
Depending on the selected multiplexer bits (bit 9, 10, 11) of Input Data
Register this output sources an image of the instant current through the
corresponding high side driver with a ratio of 1/10.000. This pin is
bidirectional. The microcontroller can overwrite the current monitor signal
to provide a PWM input for all outputs.
Testmode:
If CSN is raised above 7.5V the device will enter the test mode. In test
mode this output can be used to measure some internal signals (see
10
CSN
Chip select not input / Testmode
.
This input is low active and requires CMOS logic levels. The serial data
transfer between L9951 and micro controller is enabled by pulling the
input CSN to low level. If an input voltage of more than 7.5V is applied to
CSN pin the L9951 will be switched into a test mode.
11
DO
Serial data output .
The diagnosis data is available via the SPI and this tristate-output. The
output will remain in tristate, if the chip is not selected by the input CSN
(CSN = high).
12
VCC
Logic supply voltage .
For this input a ceramic capacitor as close as possible to GND is
recommended.
13
CLK
Serial clock input .
This input controls the internal shift register of the SPI and requires
CMOS logic levels.
相關PDF資料 |
PDF描述 |
|---|---|
| L9952GXP | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO36 |
| L9952GXPTR | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO36 |
| L99H01QF | BRUSH DC MOTOR CONTROLLER, PQFP32 |
| L99H01XPTR | BRUSH DC MOTOR CONTROLLER, PDSO36 |
| L99PM62XP | 4-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9951XP | 功能描述:馬達/運動/點火控制器和驅動器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9951XPTR | 功能描述:馬達/運動/點火控制器和驅動器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9952 | 制造商:STMicroelectronics 功能描述: |
| L9952GXP | 功能描述:馬達/運動/點火控制器和驅動器 Power management system IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9952GXPTR | 功能描述:馬達/運動/點火控制器和驅動器 Power management system IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。