- 您現在的位置：買賣IC網 > PDF目錄383255 > L9949 (意法半導體) DOOR ACTUATOR DRIVER PDF資料下載
參數資料
| 型號： | L9949 |
| 廠商： | 意法半導體 |
| 英文描述： | DOOR ACTUATOR DRIVER |
| 中文描述： | 門執行器驅動 |
| 文件頁數： | 12/20頁 |
| 文件大?。?/td> | 334K |
| 代理商： | L9949 |
L9949
12/20
Figure 7. Functional Block Diagram
FUNCTIONAL DESCRIPTION OF THE SPI
Serial Peripheral Interface (SPI)
This device uses a standard SPI to communicate with a microcontroller. The SPI can be driven by a microcontroller
with its SPI peripheral running in either of the two following modes: CPOL = CPHA = 0 or CPOL = CPHA = 1.
For these two modes, input data is sampled by the low to high transition of the clock CLK, and output data is
changed from the high to low transition of CLK.
The difference of these two modes is the standby polarity of the CLK. For CPOL = 0 the CLK remains low and
for CPOL = 1 the CLK remains high.
This device is not limited to microcontrollers with a build-in SPI. Only three CMOS-compatible output pins and
one input pin will be needed to communicate with the device. A fault condition can be detected by setting CSN
to low. If CSN = 0, the DO-pin will reflect the status bit 0 (fault condition) of the device which is a logical-or of all
bits in the status registers 0 and 1. The microcontroller can poll the status of the device without the need of a
full SPI-communication cycle.
Note:
In contrast to the SPI-standard the least significant bit (LSB) will be transfered first (see. FIGURE 8).
Chip Select not (CSN)
The input pin is used to select the serial interface of this device. When CSN is high, the output pin (DO) will be
in high impedance state. A low signal will activate the output driver and a serial communication can be started.
Serial Data In (DI)
The input pin is used to transfer data serial into the device. The data applied to the DI will be sampled at the
DI (pin 7)
DO (pin 17)
CLK (pin 6)
CSN (pin 14)
HS
LS
VS (pin5)
HS
LS
VS (pin5)
HS
LS
VS (pin5)
VS (pin13)
VS (pin13)
VS (pin8)
VS (pin8)
VS (pin18)
ESD
OUT6
(pin19)
HS
A-driver
HS
B-driver
A-driver
A-driver
A-driver
A-driver
B-driver
B-driver
B-driver
B-driver
Chargepump
Temperature
Protection
Driver Interface
Diagnostic
Power-On-Reset
SPI
Voltage and
Current
Reference
Current
Monitor
VCC
OUT3
(pin2)
OUT4
(pin3)
OUT5
(pin4)
OUT1
(pin9)
OUT2
(pin12)
VS
(pins 5,8,13,18)
GND
(pins 1,10,11,20)
CM
(pin 16)
VCC
(pin 15)
VS (pin18)
ESD
相關PDF資料 |
PDF描述 |
|---|---|
| L9950 | DOOR ACTUATOR DRIVER |
| L9950TR | DOOR ACTUATOR DRIVER |
| L9951 | DOOR ACTUATOR DRIVER |
| L9997 | DUAL HALF BRIDGE DRIVER |
| L9997ND013TR | DUAL HALF BRIDGE DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9949TR | 功能描述:功率驅動器IC Door Actuator RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| L9950 | 功能描述:馬達/運動/點火控制器和驅動器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9950_09 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Door actuator driver |
| L9950TR | 功能描述:馬達/運動/點火控制器和驅動器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L9950XP | 功能描述:馬達/運動/點火控制器和驅動器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。