參數資料
型號: L8551
廠商: Lineage Power
英文描述: Low-Power SLIC(低功耗用戶線接口(SLIC))
中文描述: 低功耗用戶接口(低功耗用戶線接口電路(SLIC))
文件頁數: 23/32頁
文件大?。?/td> 526K
代理商: L8551
Lucent Technologies Inc.
23
Data Sheet
March 1997
L8551 Low-Power SLIC
Applications
(continued)
dc Applications
(continued)
Ring Trip Detection
The ring trip circuit is a comparator that has a special in-
put section optimized for this application. The equiva-
lent circuit is shown in Figure 32, along with its use in an
application using unbalanced, battery-backed ringing.
12-3014 (C)
Figure 32. Ring Trip Equivalent Circuit and
Equivalent Application
The comparator input voltage compliance is V
CC
to
V
BAT
, and the maximum current is 240
μ
A in either
direction. Its application is straightforward. A resistance
(R
TSN
+ R
TS2
) in series with the R
TSN
input establishes a
current that is repeated in the R
TSP
input. A slightly
lower resistance (R
TSP
) is placed in series with the R
TSP
input. When ringing is being injected, no dc current
flows through R
TS1
, and so the R
TSP
input is at a lower
potential than R
TSN
. When enough dc loop current
flows, the R
TSP
input voltage increases to trip the com-
parator. In Figure 32, a low-pass filter with a double
pole at 2 Hz was implemented to prevent false ring trip.
The following example illustrates how the detection cir-
cuit of Figure 32 will trip at 12.5 mA dc loop current us-
ing a –48 V battery.
2.289 k
The current I
N
is repeated as I
P
in the positive compar-
ator input. The voltage at comparator input R
TSP
is:
V
RTSP
V
BAT
I
LOOP dc
+
=
Using this equation and the values in the example, the
voltage at input R
TSP
is –12 V during ringing injection
(I
LOOP(dc)
= 0). Input R
TSP
is therefore at a level of 5 V be-
low R
TSN
. When enough dc loop current flows through
R
TS1
to raise its dc drop to 5 V, the comparator will trip.
In this example:
Ring Ground Detection
Pin ICM sinks a current proportional to the longitudinal
loop current. It is also connected to an internal compar-
ator whose output is pin RGDET. In a ground start
application where Tip is open, the ring ground current
is half differential and half common mode. In this case,
to set the ring ground current threshold, connect a
resistor R
ICM
from pin ICM to V
CC
. Select the resistor
according to the following relation:
The above equation is shown graphically in Figure 19.
It applies for the case of Tip open. The more general
equation can be used in ground key application to
detect a common-mode current I
CM
:
+
R
TSP
R
LOOP
+
15 k
7 V
I
P
= I
N
R
TSN
R
TS2
2 M
2 M
C
RTS1
0.022 μF
C
RTS2
0.27 μF
274 k
V
RING
PHONE
HOOK SWITCH
RC PHONE
V
BAT
NRDET
R
TS1
402
R
TSP
I
N
R
TSN
I
N
–7 – (–48)
=
17.9
μ
A
=
)
R
TS1
I
P
R
TSP
×
+
×
I
LOOP dc
)
402
=
12.5 mA
=
R
ICM
k
(
)
(
228
×
)
----------------------
=
R
ICM
k
(
)
)
----------------------
=
相關PDF資料
PDF描述
L8560 Low-Power SLIC(electronic subscriber loop interface circuits ) with Ringing(帶振鈴的低功耗用戶線接口(SLIC))
L8567 SLIC for People Republic of China Applications(用于中國的用戶線接口(SLIC))
L8574D Resistive Subscriber Line Interface Circuit (SLIC), Ring Relay, and Protector (SRP) for Long Loop and TR-57 Applications(長環路和TR-57應用的電阻性用戶線接口,振鈴繼電器和保護器)
L8575 Dual-Resistive, Low-Cost Subscriber Line Interface Circuit (SLIC)(雙電阻、低價格用戶線接口)
L8576B Dual Ringing SLIC(雙通道振鈴用戶環路接口(SLIC))
相關代理商/技術參數
參數描述
L8560 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Power SLIC with Ringing
L8560AAU 制造商:Alcatel-Lucent 功能描述: 制造商:LUCENT 功能描述:
L8561 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:The UTC L8561 is a Power Factor Corrector, which can work in wide input voltage range applications (from 85V ~ 265V) with an excellent THD.
L8561_11 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:POWER FACTOR CORRECTOR
L8561G-D08-T 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:POWER FACTOR CORRECTOR