- 您現在的位置：買賣IC網 > PDF目錄384587 > L8551 (Lineage Power) Low-Power SLIC(低功耗用戶線接口（SLIC）) PDF資料下載
參數資料
| 型號： | L8551 |
| 廠商： | Lineage Power |
| 英文描述： | Low-Power SLIC(低功耗用戶線接口（SLIC）) |
| 中文描述： | 低功耗用戶接口（低功耗用戶線接口電路（SLIC）） |
| 文件頁數： | 21/32頁 |
| 文件大小： | 526K |
| 代理商： | L8551 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Lucent Technologies Inc.
21
Data Sheet
March 1997
L8551 Low-Power SLIC
Applications
(continued)
dc Applications
(continued)
Overhead Voltage
(continued)
12-2560 (C)
Figure 27. SLIC 2-Wire Output Stage
In addition to the required peak signal level, the SLIC
needs about 2 V from each power supply to bias the
amplifier circuitry. It can be thought of as an internal
saturation voltage. Combining the saturation voltage
and the peak signal level, the required overhead can be
expressed as:
where V
SAT
is the combined internal saturation voltage
between the Tip/Ring amplifiers and V
SAT
(4.0 V typ.).
R
P
(W) is the protection resistor value, R
S
is the resis-
tance of the L7581 solid-state switch, and 65 W is one-
half the dc feed resistance of the SLIC. Z
T/R
(
) is the
ac loop impedance.
Example 1: On-Hook Transmission of a Meter Pulse
Signal level: 2.2 Vrms into 200
20
protection resistors
28
solid-state switch on resistance
I
LOOP
= 0 (on-hook transmission of the metering
signal)
= 10.6 V
Accounting for V
SAT
tolerance of 0.5 V, a nominal over-
head of 10.1 V would ensure transmission of an undis-
torted 2.2 V metering signal.
Adjusting Overhead Voltage
To adjust the open loop 2-wire voltage, pin DCR is
programmed at the midpoint of a resistive divider from
ground to either –5 V or V
BAT
. In the case of –5 V, the
overhead voltage will be independent of the battery
voltage. Figure 28 shows the equivalent input circuit to
adjust the overhead.
12-2562 (C)
Figure 28. Equivalent Circuit for Adjusting the
Overhead Voltage
The overhead voltage is programmed by using the fol-
lowing equation:
–
V
T/R
[Z
T/R
]
V
AMP
–
+
R
DC
/2
R
P
R
P
+
R
DC
/2
V
OH
V
SAT
1
-------------+
Z
T R
+
)
+
V
--
T R
+
=
V
OH
4.0
1
2 20
28
65
+
200
+
)
+
2 2.2
)
+
=
DCR
25 k
±
30%
R1
R2
–5 V
V
OH
6.5
4V
DCR
–
=
6.5
4
5
||
R
2
R
1
25k
+
||
R
1
25k
+
||
-------------------------------------
×
–
–
=
6.5
20
R
2
-------------------------------------
+
=
相關PDF資料 |
PDF描述 |
|---|---|
| L8560 | Low-Power SLIC（electronic subscriber loop interface circuits ） with Ringing(帶振鈴的低功耗用戶線接口（SLIC）) |
| L8567 | SLIC for People Republic of China Applications(用于中國的用戶線接口（SLIC）) |
| L8574D | Resistive Subscriber Line Interface Circuit (SLIC), Ring Relay, and Protector (SRP) for Long Loop and TR-57 Applications(長環路和TR-57應用的電阻性用戶線接口，振鈴繼電器和保護器) |
| L8575 | Dual-Resistive, Low-Cost Subscriber Line Interface Circuit (SLIC)(雙電阻、低價格用戶線接口) |
| L8576B | Dual Ringing SLIC(雙通道振鈴用戶環路接口（SLIC）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L8560 | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Power SLIC with Ringing |
| L8560AAU | 制造商:Alcatel-Lucent 功能描述: 制造商:LUCENT 功能描述: |
| L8561 | 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:The UTC L8561 is a Power Factor Corrector, which can work in wide input voltage range applications (from 85V ~ 265V) with an excellent THD. |
| L8561_11 | 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:POWER FACTOR CORRECTOR |
| L8561G-D08-T | 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:POWER FACTOR CORRECTOR |
發布緊急采購，3分鐘左右您將得到回復。