- 您現在的位置：買賣IC網 > PDF目錄384587 > L7585G (Lineage Power) Full-Feature, Low-Power SLIC and Switch(特點齊全的低功耗用戶接口和開關) PDF資料下載
參數資料
| 型號： | L7585G |
| 廠商： | Lineage Power |
| 英文描述： | Full-Feature, Low-Power SLIC and Switch(特點齊全的低功耗用戶接口和開關) |
| 中文描述： | 全功能，低功耗SLIC和開關（特點齊全的低功耗用戶接口和開關） |
| 文件頁數： | 10/22頁 |
| 文件大?。?/td> | 560K |
| 代理商： | L7585G |
10
Lucent Technologies Inc.
Data Sheet
May 2000
L7585G Full-Feature, Low-Power SLIC and Switch
Electrical Characteristics
In general, minimum and maximum values are testing requirements. However, some parameters may not be
tested in production because they are guaranteed by design and device characterization. Typical values reflect the
design center or nominal value of the parameter; they are for information only and are not a requirement. Minimum
and maximum values apply across the entire temperature range (–40 °C to +85 °C) and entire battery range
(–35 V to –60 V). Unless otherwise specified, typical is defined as 25 °C, V
CCA
= +5.0 V, V
CCD
= +5.0 V,
V
SP
= +10 V, V
BAT
= –48 V. Positive currents flow into the device.
* Not to exceed 26 grams of water per kilogram of dry air.
This parameter is not tested in production; it is guaranteed by design and device characterization.
1. The ringing source may be either of the following:
a) The ringing source consists of the ac and dc voltages added together (battery-backed ringing); the ringing return is ground. In this case,
bit B3 will always be a 1 when ringing is applied.
b) The ringing source consists of only the ac voltage (earth-backed ringing); the ringing return is the dc voltage. In this case, bit B3 will
always be a 0 when ringing is applied.
2. NDET must also indicate ring trip when the ac ringing voltage is absent (<5 Vrms) from the ringing source.
3. Pretrip ringing must not be tripped by a 10 k
resistor in parallel with an 8 μF capacitor applied across tip and ring.
Table 4. Operating Conditions and Powering
Parameter
Min
–40
5
Typ
—
—
Max
85
95*
Unit
°C
%RH
Temperature Range
Humidity Range
Supply Voltages:
V
CCA
V
CCD
V
SP
V
BAT
V
CCA
—V
CCD
D
GND
—A
GND
Supply Currents (all states, no loop current):
I
CCA
+ I
CCD
(+5 V)
IV
SP
(+10 V)
I
BAT
(–48 V)
Total Power Dissipation (all states, no loop current)
(V
CC
= +5 V; V
SP
= +10 V; V
BAT
= –48 V)
Power Supply Rejection (tip/ring and transmit)
:
V
CCA
(500 Hz—3 kHz; 50 mVrms ripple)
V
CCD
(500 Hz—3 kHz; 50 mVrms ripple)
V
SP
(500 Hz—3 kHz; 250 mVrms ripple)
V
BAT
(500 Hz—3 kHz; 50 mVrms ripple)
Thermal
:
Thermal Resistance (still air)
Operating T
JC
4.75
4.75
8.0
–35
—
—
5.0
5.0
10
–48
—
—
5.5
5.5
12.0
–60
±0.5
±0.25
V
V
V
V
V
V
—
—
—
—
4.9
45
–3.1
175
7.0
200
–4.0
200
mA
μA
mA
mW
30
45
45
45
40
—
—
—
—
—
—
—
dB
dB
dB
dB
—
—
—
—
47
155
°C/W
°C
Table 5. Ring Trip Detector
Parameter
Min
±2.5
±12
Typ
±3
±15
Max
±3.5
±18
Unit
V
V
Voltage at input that will cause ring trip after appropriate zero crossings.
Voltage at input that will cause immediate ring trip.
Ringing Source
1
:
Frequency (f)
dc Voltage
ac Voltage
Ring Trip (NDET = 0)
2, 3
:
Loop Resistance
Trip Time
NDET Valid
19
–39.5
60
20
—
—
28
–57
105
Hz
V
Vrms
2000
—
—
—
—
—
—
200
80
ms
ms
相關PDF資料 |
PDF描述 |
|---|---|
| L7590C | Telephone Ringing Driver(電話振鈴驅動器) |
| L7591 | Subscriber Line Interface Circuit Protector(用戶線接口保護器) |
| L7597 | Resistive Subscriber Line Interface Circuit (SLIC), Ring Relay, and Protector (SRP) for Short Loop and TA-909 Applications(用于短環路和TA-909的電阻性用戶線接口、振鈴繼電器和保護器) |
| L7808AB | Precision 1A regulators(精密1A穩壓器) |
| L7810CD2T-TR1 | 5.0 AMP POSITIVE VOLTAGE REGULATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L7590 | 制造商:Bahco 功能描述:PLIER ROUND NOSE 121MM 制造商:Bahco 功能描述:PLIER, ROUND NOSE 121MM |
| L7590C | 制造商:AGERE 制造商全稱:AGERE 功能描述:Telephone Ringing Driver |
| L7590CAE | 制造商:Alcatel-Lucent 功能描述:7590CAE |
| L7591 | 制造商:AGERE 制造商全稱:AGERE 功能描述:Subscriber Line Interface Circuit Protector |
| L75F50R | 制造商:Ohmite Mfg Co 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。