參數資料
型號： L6563H
廠商： STMICROELECTRONICS
元件分類： 穩壓器
英文描述： POWER FACTOR CONTROLLER, PDSO16
封裝： ROHS COMPLIANT, SOP-16
文件頁數： 47/48頁
文件大小： 1634K
代理商： L6563H
Pin connection
L6563H
8/48
Doc ID 16047 Rev 2
3
Pin connection
Figure 2.
Pin connection
Table 3.
Pin description
n°
Name
Function
1INV
Inverting input of the error amplifier. The information on the output voltage of the PFC pre-
regulator is fed into the pin through a resistor divider.
The pin normally features high impedance but, if the tracking boost function is used, an internal
current generator programmed by TBO (pin 6) is activated. It sinks current from the pin to
change the output voltage so that it tracks the mains voltage.
2COMP
Output of the error amplifier. A compensation network is placed between this pin and INV (pin
1) to achieve stability of the voltage control loop and ensure high power factor and low THD.
To avoid uncontrolled rise of the output voltage at zero load, when the voltage on the pin falls
below 2.4 V the gate driver output is inhibited (burst-mode operation).
3MULT
Mains input to the multiplier. This pin is connected to the rectified mains voltage via a resistor
divider and provides the sinusoidal reference to the current loop. The voltage on this pin is used
also to derive the information on the RMS mains voltage.
4CS
Input to the PWM comparator. The current flowing in the MOSFET is sensed through a resistor,
the resulting voltage is applied to this pin and compared with an internal reference to determine
MOSFET’s turn-off.
A second comparison level at 1.7 V detects abnormal currents (e.g. due to boost inductor
saturation) and, on this occurrence, activates a safety procedure that temporarily stops the
converter and limits the stress of the power components.
5VFF
Second input to the multiplier for 1/V2 function. A capacitor and a parallel resistor must be
connected from the pin to GND. They complete the internal peak-holding circuit that derives the
information on the RMS mains voltage. The voltage at this pin, a dc level equal to the peak
voltage on pin MULT (3), compensates the control loop gain dependence on the mains voltage.
Never connect the pin directly to GND but with a resistor ranging from 100 k
Ω (minimum) to 2 M
Ω (maximum).
6TBO
Tracking boost function. This pin provides a buffered VFF voltage. A resistor connected
between this pin and GND defines a current that is sunk from pin INV (1). In this way, the output
voltage is changed proportionally to the mains voltage (tracking boost). If this function is not
used leave this pin open.
相關PDF資料
PDF描述
L6565N 0.7 A SWITCHING CONTROLLER, PDIP8
L6615N 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8
L6711TR 2 A SWITCHING CONTROLLER, 178 kHz SWITCHING FREQ-MAX, PQFP48
L6711 2 A SWITCHING CONTROLLER, 178 kHz SWITCHING FREQ-MAX, PQFP48
L6714TR SWITCHING CONTROLLER, 170 kHz SWITCHING FREQ-MAX, PQFP64
相關代理商/技術參數
參數描述
L6563HTR 功能描述:功率因數校正 IC 700V 6mA Start-Up Transition-Mode PFC RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel
L6563S 功能描述:功率因數校正 IC Transition Mode PFC 5mA 90uA 1.5% Ref RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel
L6563STR 功能描述:功率因數校正 IC Transition Mode PFC 5mA 90uA 1.5% Ref RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel
L6563TR 功能描述:功率因數校正 IC POWER SUPPLY RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel
L6564 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:10 pin transition-mode PFC controller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*