- 您現在的位置：買賣IC網 > PDF目錄384584 > L6223 (意法半導體) DMOS Programmable High Speed Unipolar Stepper Motor Driver(高速單極步進電機驅動器) PDF資料下載
參數資料
| 型號： | L6223 |
| 廠商： | 意法半導體 |
| 英文描述： | DMOS Programmable High Speed Unipolar Stepper Motor Driver(高速單極步進電機驅動器) |
| 中文描述： | DMOS的可編程高速單極性步進電機驅動器（高速單極步進電機驅動器） |
| 文件頁數： | 31/33頁 |
| 文件大?。?/td> | 1078K |
| 代理商： | L6223 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁
Figure36:
PeaktransientRthpulsewidthandDutyCycle.
Notes on the p.c.b. design.
We recommend to observe the following layout
rules to avoid application problems associated
with ground loops and anomalous recirculation
currents. The by-pass capacitors for the power
and logic supply must to be kept as close to the
IC as possible.
It’s important to separate on the PCB board the
logic and the power grounds avoiding that
grounds traces of the logic signals cross the
ground traces of the power signals. The starpoint
grounding, the point of the board in which the
logic ground meets the power ground, should be
kept far enough away from where the power
ground traces terminate to ground (sense resis-
tors and protection zener diodes traces). This
avoids interference with the logic signals. Be-
cause the IC uses the board as a heatsink the
dissipating copper area must be sized in accord-
ance with the requiredvalue of R
thj-amb
. It’s impor-
tant to provide a good filter for the logic supply,
especially for the resistor of the oscillator net-
work. In addition, the capacitor ground of the RC
network must be as clean as possible. When the
ground is used also to heatsink, it is helpful to
use either a polistyrin capacitor or one with a low
temperature coefficient. The value of the boot-
strap capacitor is not a critical parameter, never-
theless the use of a capacitor of 10nF
±
20% is
recommended. A non-inductive resistor is the
best way to implement the sensing, but when that
is not possible, more metalfilm resistors of the
same value can be paralleled.
L6223
31/33
相關PDF資料 |
PDF描述 |
|---|---|
| L6226 | DMOS DUAL FULL BRIDGE DRIVER |
| L6226D | DMOS DUAL FULL BRIDGE DRIVER |
| L6226N | DMOS DUAL FULL BRIDGE DRIVER |
| L6226PD | DMOS DUAL FULL BRIDGE DRIVER |
| L6228 | DMOS DRIVER FOR BIPOLAR STEPPER MOTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6223A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| L6225 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:DMOS DUAL FULL BRIDGE DRIVER |
| L6225_03 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:DMOS DUAL FULL BRIDGE DRIVER |
| L6225D | 功能描述:馬達/運動/點火控制器和驅動器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6225DTR | 功能描述:馬達/運動/點火控制器和驅動器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。