- 您現在的位置：買賣IC網 > PDF目錄43899 > L6208D013TR (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, 5.6 A, PDSO24 PDF資料下載
參數資料
| 型號： | L6208D013TR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 5.6 A, PDSO24 |
| 封裝： | ROHS COMPLIANT, SOP-24 |
| 文件頁數： | 9/27頁 |
| 文件大?。?/td> | 453K |
| 代理商： | L6208D013TR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
17/27
L6208
Figure 20 shows the Overcurrent Detection operation. The Disable Time tDISABLE before recovering normal oper-
ation can be easily programmed by means of the accurate thresholds of the logic inputs. It is affected whether by
CEN and REN values and its magnitude is reported in Figure 21. The Delay Time tDELAY before turning off the
bridge when an overcurrent has been detected depends only by CEN value. Its magnitude is reported in Figure 22.
CEN is also used for providing immunity to pin EN against fast transient noises. Therefore the value of CEN
should be chosen as big as possible according to the maximum tolerable Delay Time and the REN value should
be chosen according to the desired Disable Time.
The resistor REN should be chosen in the range from 2.2K to 180K. Recommended values for REN and CEN
are respectively 100K
and 5.6nF that allow obtaining 200s Disable Time.
Figure 20. Overcurrent Protection Waveforms
ISOVER
IOUT
Vth(ON)
Vth(OFF)
VEN(LOW)
VDD
tOCD(ON)
tD(ON)EN
tEN(FALL)
tEN(RISE)
tDISABLE
tDELAY
tOCD(OFF)
tD(OFF)EN
VEN
BRIDGE
ON
OFF
OCD
ON
OFF
D02IN1400
相關PDF資料 |
PDF描述 |
|---|---|
| L6219R013TR | STEPPER MOTOR CONTROLLER, 1 A, PDSO24 |
| L6223 | STEPPER MOTOR CONTROLLER, 6 A, PDIP20 |
| L6225PDTR | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO20 |
| L6225PD | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO20 |
| L6225D | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6208D013TR-CUT TAPE | 制造商:ST 功能描述:L6208 Series Dual 52 V 5.6 A DMOS Driver for Bipolar Stepper Motor - SOIC-24 |
| L6208N | 功能描述:馬達/運動/點火控制器和驅動器 DMOS Stepper Motor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6208PD | 功能描述:馬達/運動/點火控制器和驅動器 DMOS Stepper Motor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6208PD013TR | 功能描述:馬達/運動/點火控制器和驅動器 DMOS Stepper Motor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6208Q | 功能描述:馬達/運動/點火控制器和驅動器 DMOS Driver Bipolar 5.6A 100kHz 8 to 52V RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。