- 您現在的位置：買賣IC網 > PDF目錄43899 > L6208D013TR (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, 5.6 A, PDSO24 PDF資料下載
參數資料
| 型號： | L6208D013TR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 5.6 A, PDSO24 |
| 封裝： | ROHS COMPLIANT, SOP-24 |
| 文件頁數： | 27/27頁 |
| 文件大?。?/td> | 453K |
| 代理商： | L6208D013TR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁
9/27
L6208
Figure 5. Overcurrent Detection Timing Definition
CIRCUIT DESCRIPTION
POWER STAGES and CHARGE PUMP
The L6208 integrates two independent Power MOS Full Bridges. Each Power MOS has an RDS(ON) = 0.3
(typ-
ical value @ 25°C), with intrinsic fast freewheeling diode. Switching patterns are generated by the PWM Current
Controller and the Phase Sequence Generator (see below). Cross conduction protection is achieved using a
dead time (tDT = 1
s typical value) between the switch off and switch on of two Power MOSFETSs in one leg of
a bridge.
Pins VSA and VSB MUST be connected together to the supply voltage VS. The device operates with a supply
voltage in the range from 8V to 52V. It has to be noticed that the RDS(ON) increases of some percents when the
supply voltage is in the range from 8V to 12V (see Fig. 34 and 35).
Using N-Channel Power MOS for the upper transistors in the bridge requires a gate drive voltage above the
power supply voltage. The bootstrapped supply voltage VBOOT is obtained through an internal Oscillator and few
external components to realize a charge pump circuit as shown in Figure 6. The oscillator output (VCP) is a
square wave at 600KHz (typical) with 10V amplitude. Recommended values/part numbers for the charge pump
circuit are shown in Table 1.
Table 1. Charge Pump External Components Values
CBOOT
220nF
CP
10nF
RP
100
D1
1N4148
D2
1N4148
ISOVER
90%
10%
IOUT
VEN
tOCD(OFF)
tOCD(ON)
D02IN1399
ON
OFF
BRIDGE
相關PDF資料 |
PDF描述 |
|---|---|
| L6219R013TR | STEPPER MOTOR CONTROLLER, 1 A, PDSO24 |
| L6223 | STEPPER MOTOR CONTROLLER, 6 A, PDIP20 |
| L6225PDTR | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO20 |
| L6225PD | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO20 |
| L6225D | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6208D013TR-CUT TAPE | 制造商:ST 功能描述:L6208 Series Dual 52 V 5.6 A DMOS Driver for Bipolar Stepper Motor - SOIC-24 |
| L6208N | 功能描述:馬達/運動/點火控制器和驅動器 DMOS Stepper Motor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6208PD | 功能描述:馬達/運動/點火控制器和驅動器 DMOS Stepper Motor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6208PD013TR | 功能描述:馬達/運動/點火控制器和驅動器 DMOS Stepper Motor RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| L6208Q | 功能描述:馬達/運動/點火控制器和驅動器 DMOS Driver Bipolar 5.6A 100kHz 8 to 52V RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。