- 您現在的位置：買賣IC網 > PDF目錄4597 > KSZ8995FQI (Micrel Inc)IC SWITCH 10/100 5PORT 128-PQFP PDF資料下載
參數資料
| 型號： | KSZ8995FQI |
| 廠商： | Micrel Inc |
| 文件頁數： | 27/89頁 |
| 文件大小： | 0K |
| 描述： | IC SWITCH 10/100 5PORT 128-PQFP |
| 標準包裝： | 66 |
| 系列： | * |
| 產品目錄頁面： | 1081 (CN2011-ZH PDF) |
| 配用： | 576-3872-ND - BOARD EVALUATION FOR KSZ8995FQ |
| 其它名稱： | 576-3300 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁
Micrel, Inc.
KS8995MA/FQ
October 2011
33
M9999-102611-3.0
Half-Duplex Back Pressure
The KS8995MA/FQ also provides a half-duplex back-pressure option (Note: this is not in IEEE 802.3 standards). The
activation and deactivation conditions are the same as the ones given for full-duplex mode. If back pressure is required,
the KS8995MA/FQ sends preambles to defer the other station's transmission (carrier sense deference). To avoid jabber
and excessive deference as defined in IEEE 802.3 standard, after a certain period of time, the KS8995MA/FQ
discontinues carrier sense but raises it quickly after it drops packets to inhibit other transmissions. This short silent time
(no carrier sense) is to prevent other stations from sending out packets and keeps other stations in a carrier sense
deferred state. If the port has packets to send during a back pressure situation, the carrier-sense-type back pressure is
interrupted and those packets are transmitted instead. If there areno more packets to send, carrier-sense-type back
pressure becomes active again until switch resources are free. If a collision occurs, the binary exponential backoff
algorithm is skipped and carrier sense is generated immediately, reducing the chanceof further colliding and maintaining
carrier sense to prevent reception of packets. To ensure no packet loss in 10BASE-T or 100BASE-TX half-duplex modes,
the user must enable the following:
Aggressive backoff (Register 3, Bit 0)
No excessive collision drop (Register 4, Bit 3)
Back pressure (Register 4, Bit 5)
These bits are not set as the default because this is not the IEEE standard.
Broadcast Storm Protection
The KS8995MA/FQ has an intelligent option to protect the switch system from receiving too many broadcast packets.
Broadcastpackets are normally forwarded to all ports except the source port and thus use too many switch resources
(bandwidth and available space in transmit queues). The KS8995MA/FQ has the option to include “multicast packets” for
storm control. The broadcast storm rate parameters are programmed globally and can be enabled or disabled on a per
port basis. The rate is basedon a 50ms interval for 100BT and a 500ms interval for 10BT. At the beginning of each
interval, the counter is cleared to zero and the rate limit mechanism starts to count the number of bytes during the interval.
The rate definition is described in Registers 6 and 7. The default setting for Registers 6 and 7 is 0x4A (74 decimal). This is
equal to a rate of 1%, calculated as follows:
148,800 frames/sec
× 50ms/interval × 1% = 74 frames/interval (approximately) = 0×4A frames/interval
MII Interface Operation
The media independent interface (MII) is specified by the IEEE 802.3 committee and provides a common interface
between physical layer and MAC layer devices. The KS8995MA/FQ provides two such interfaces. The MII-P5 interface is
used to connectto the fifth PHY, whereas the MII-SW interface is used to connect to the fifth MAC. Each of these MII
interfaces contains two distinct groups of signals, one for transmission and the other for receiving. Table 1 describes the
signals used in the MII-P5 interface.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9970BCPZ | IC PROCESSOR CCD SIGNAL 32LFCSP |
| ADP5587ACPZ-R7 | IC EXPANDER/KEYBOARD CTRLR |
| LFXP3E-4TN144C | IC FPGA 3.1KLUTS 100I/O 144-TQFP |
| LFXP3C-4TN144C | IC FPGA 3.1KLUTS 100I/O 144-TQFP |
| FMC15DRYN-S93 | CONN EDGECARD 30POS .100 DIP SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8995M | 功能描述:以太網 IC 5 Port 10/100 Switch with PHY and Frame Buffers (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8995MA | 功能描述:以太網 IC 5 Port 10/100 Switch with PHY and Frame Buffers (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8995MA4 | 功能描述:IC SWITCH 5-PORT 10/100 128PQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
| KSZ8995MAB3 | 功能描述:IC SWITCH 5-PORT 10/100 128PQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
| KSZ8995MA-EVAL | 功能描述:以太網開發工具 KSZ8995MA Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。