- 您現在的位置：買賣IC網 > PDF目錄1932 > KSZ8995FQ (Micrel Inc)IC SWITCH 10/100 5PORT 128-PQFP PDF資料下載
參數資料
| 型號： | KSZ8995FQ |
| 廠商： | Micrel Inc |
| 文件頁數： | 30/89頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH 10/100 5PORT 128-PQFP |
| 標準包裝： | 66 |
| 系列： | * |
| 產品目錄頁面： | 1081 (CN2011-ZH PDF) |
| 配用： | 576-3872-ND - BOARD EVALUATION FOR KSZ8995FQ |
| 其它名稱： | 576-3077 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁
Micrel, Inc.
KS8995MA/FQ
October 2011
36
M9999-102611-3.0
SNI Interface Operation
The serial network interface (SNI) is compatible with some controllers used for network layer protocol processing. This
interface can be directly connected to these types of devices. The signals are divided into two groups, one for
transmission and the other for reception. The signals involved are described in Table 3.
SNI Signal
Description
KS8995MA/FQ Signal
TXEN
Transmit Enable
SMTXEN
TXD
Serial Transmit Data
SMTXD[0]
TXC
Transmit Clock
SMTXC
COL
Collision Detection
SCOL
CRS
Carrier Sense
SMRXDV
RXD
Serial Receive Data
SMRXD[0]
RXC
Receive Clock
SMRXC
Table 3. SNI Signals
This interface is a bit-wide data interface and therefore runs at the network bit rate (not encoded). An additional signal on
the transmit side indicates when data is valid. Likewise, the receive side has an indicator that conveys when the data is
valid.
For half-duplex operation there is a signal that indicates a collision has occurred during transmission.
Advanced Functionality
Spanning Tree Support
Port 5 is the designated port for spanning tree support.
The other ports (Port 1 – Port 4) can be configured in one of the five spanning tree states via “transmit enable,” “receive
enable,” and “l(fā)earning disable” register settings in Registers 18, 34, 50, and 66 for Ports 1, 2, 3, and 4, respectively. The
following description shows the port setting and software actions taken for each of the five spanning tree states.
Disable state: the port should not forward or receive any packets. Learning is disabled.
Port setting: "transmit enable = 0, receive enable = 0, learning disable = 1."
Software action: the processor should not send any packets to the port. The switch may still send specific packets to the
processor (packets that match some entries in the static table with “overriding bit” set) and the processor should discard
those packets. Note: processor is connected to port 5 via MII interface. Address learning is disabled on the port in this
state.
Blocking state: only packets to the processor are forwarded. Learning is disabled.
Port setting: "transmit enable = 0, receive enable = 0, learning disable = 1"
Software action: the processor should not send any packets to the port(s) in this state. The processor should program the
“Static MAC table” with the entries that it needs to receive (e.g., BPDU packets). The “overriding” bit should also be set so
that the switch will forward those specific packets to the processor. Address learning is disabled on the port in this state.
Listening state: only packets to and from the processor are forwarded. Learning is disabled.
Port setting: "transmit enable = 0, receive enable = 0, learning disable = 1.
"Software action: The processor should program the static MAC table with the entries that it needs to receive (e.g. BPDU
packets). The “overriding” bit should be set so that the switch will forward those specific packets to the processor. The
processor may send packets to the port(s) in this state, see “Special Tagging Mode” section for details. Address learning
is disabled on the port in this state.
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8995MA | IC SWITCH 10/100 5PORT 128PQFP |
| KSZ8995MI | IC SWITCH 5-PORT 10/100 128PQFP |
| KSZ9021GN TR | TXRX ETHERNET GB GMII/MII 64MLF |
| KSZ9021GQI | TXRX GIG ETH GMII/MII 128-PQFP |
| KSZ9021RL | IC TXRX 10/100/1000 SGL 64LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8995FQ-EVAL | 功能描述:以太網開發工具 Integrated 5-Port Switch with Fiber on Port 3 & 4 Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8995FQI | 功能描述:以太網 IC 5 Port 10/100 Switch with PHY and Frame Buffers (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8995M | 功能描述:以太網 IC 5 Port 10/100 Switch with PHY and Frame Buffers (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8995MA | 功能描述:以太網 IC 5 Port 10/100 Switch with PHY and Frame Buffers (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8995MA4 | 功能描述:IC SWITCH 5-PORT 10/100 128PQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
發布緊急采購，3分鐘左右您將得到回復。