2C master mode by setting the KS8993M strap-" />
參數資料
型號： KSZ8993M
廠商： Micrel Inc
文件頁數： 33/85頁
文件大?。?/td> 0K
描述： IC SWITCH 10/100 3PORT 128PQFP
標準包裝： 66
系列： *
類型： *
應用： *
安裝類型： 表面貼裝
封裝/外殼： 128-BFQFP
供應商設備封裝： 128-PQFP（14x20）
包裝： 托盤
產品目錄頁面： 1081 (CN2011-ZH PDF)
其它名稱： 576-1037
Micrel, Inc.
KS8993M/ML/MI
April 2005
39
M9999-041205
2.
Enable I
2C master mode by setting the KS8993M strap-in pins, PS[1:0] (pins 100 and 101, respectively) to
“00”.
3.
Check to ensure that the KS8993M reset signal input, RST_N (pin 67), is properly connected to the external
reset source at the board level.
4.
Program the desired configuration data into the EEPROM.
5.
Place the EEPROM on the board and power up the board.
6.
Assert an active-low reset to the RST_N pin of the KS8993M. After reset is de-asserted, the KS8993M will
begin reading the configuration data from the EEPROM. The KS8993M will check that the first byte read from
the EEPROM is “93”. If this value is correct, EEPROM configuration will continue. If not, EEPROM
configuration access is denied and all other data sent from the EEPROM will be ignored by the KS8993M.
The configuration access time (tprgm) is less than 15ms.
Note: For proper operation, check to ensure that the KS8993M PWRDN input signal (pin 36) is not asserted
during the reset operation. The PWRDN input is active low.
I
2C Slave Serial Bus Configuration
In managed mode, the KS8993M can be configured as an I
2C slave device. In this mode, an I2C master device
(external controller/CPU) has complete programming access to the KS8993M’s 128 registers. Programming
access includes the Global Registers, Port Registers, Advanced Control Registers and indirect access to the
“Static MAC Table”, “VLAN Table”, “Dynamic MAC Table,” and “MIB Counters.” The tables and counters are
indirectly accessed via registers 110 thru 120.
In I
2C slave mode, the KS8993M operates like other I2C slave devices. Addressing the KS8993M’s 8 bit registers
is similar to addressing Atmel’s AT24C02 EEPROM’s memory locations. Details of I
2C read/write operations and
related timing information can be found in the AT24C02 Datasheet.
Two fixed 8 bits device addresses are used to address the KS8993M in I
2C slave mode. One is for read; the other
is for write. The addresses are as follow:
1011_1111 <read>
1011_1110 <write>
The following is a sample procedure for programming the KS8993M using the I
2C slave serial bus:
1.
Enable I
2C slave mode by setting the KS8993M strap-in pins PS[1:0] (pins 100 and 101, respectively) to “01”.
2.
Power up the board and assert reset to the KS8993M. After reset, the “Start Switch” bit (register 1 bit 0) will
be set to ‘0’.
3.
Configure the desired register settings in the KS8993M, using the I
2C write operation.
4.
Read back and verify the register settings in the KS8993M, using the I
2C read operation.
5.
Write a ‘1’ to the “Start Switch” bit to start the KS8993M with the programmed settings.
Note: The “Start Switch” bit cannot be set to ‘0’ to stop the switch after an ‘1’ is written to this bit. Thus, it is
recommended that all switch configuration settings are programmed before the “Start Switch” bit is set to ‘1’.
Some of the configuration settings, such as “Aging enable”, “Auto Negotiation Enable”, “Force Speed” and “Power
down” can be programmed after the switch has been started.
SPI Slave Serial Bus Configuration
In managed mode, the KS8993M can be configured as a SPI slave device. In this mode, a SPI master device
(external controller/CPU) has complete programming access to the KS8993M’s 128 registers. Programming
access includes the Global Registers, Port Registers, Advanced Control Registers and indirect access to the
“Static MAC Table”, “VLAN Table”, “Dynamic MAC Table” and “MIB Counters”. The tables and counters are
indirectly accessed via registers 110 thru 120.
The KS8993M supports two standard SPI commands: ‘0000_0011’ for data read and ‘0000_0010’ for data write.
SPI multiple read and multiple write are also supported by the KS8993M to expedite register read back and
register configuration, respectively.
相關PDF資料
PDF描述
KSZ8995M IC SWITCH 10/100 5PORT 128PQFP
RSM40DTAT CONN EDGECARD 80POS R/A .156 SLD
LFEC6E-3QN208C IC FPGA 6.1KLUTS 147I/O 208-PQFP
LFEC6E-3Q208C IC FPGA 6.1KLUTS 147I/O 208-PQFP
RMM40DTAT CONN EDGECARD 80POS R/A .156 SLD
相關代理商/技術參數
參數描述
KSZ8993MA5 功能描述:IC SWITCH 10/100 W/TXRX 128PQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝
KSZ8993M-EVAL 功能描述:以太網開發工具 KSZ8993M Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
KSZ8993MI 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-Ld PQFP (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8993ML 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-Ld PQFP(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8993ML-EVAL 功能描述:以太網開發工具 KSZ8993ML Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*