hbwhelp@micrel.com or (408) 955-1690 On the transmit " />
參數資料
型號： KSZ8993FL
廠商： Micrel Inc
文件頁數： 29/100頁
文件大?。?/td> 0K
描述： IC CONV MED 10/100 SGL 128PQFP
標準包裝： 66
系列： *
類型： *
應用： *
安裝類型： 表面貼裝
封裝/外殼： 128-BFQFP
供應商設備封裝： 128-PQFP（14x20）
包裝： 托盤
產品目錄頁面： 1081 (CN2011-ZH PDF)
其它名稱： 576-1035
Micrel, Inc.
KS8993F/FL
June 2009
34
M9999-062509
hbwhelp@micrel.com or (408) 955-1690
On the transmit side, the KS8993F has intelligent and efficient means to determine when to invoke flow control. The
flow control is based on the availability of system resources, including available buffers, available transmit queues and
available receive queues.
The KS8993F will flow control a port, which just received a packet, if the destination port resource is being used up.
The KS8993F will issue a flow control frame (XOFF), containing the maximum pause time defined in IEEE standard
802.3x. Once the resource is freed up, the KS8993F will send out the other flow control frame (XON) with zero pause
time to turn off the flow control (turn on transmission to the port). A hysteresis feature is provided to prevent the flow
control mechanism from being activated and deactivated too many times.
The KS8993F will flow control all ports if the receive queue becomes full.
2.4.12 Half Duplex Back Pressure
A half-duplex back-pressure option (Note: not in IEEE 802.3 standards) is also provided.
The activation and
deactivation conditions are the same as the above in full duplex mode. If back-pressure is required, the KS8993F will
send preambles to defer the other stations' transmission (carrier sense deference). To avoid jabber and excessive
deference defined in 802.3 standard, after a certain time it will discontinue the carrier sense but it will raise the carrier
sense quickly. This short silent time (no carrier sense) is to prevent other stations from sending out packets and keeps
other stations in carrier sense deferred state.
If the port has packets to send during a back-pressure situation, the
carrier sense type back-pressure will be interrupted and those packets will be transmitted instead. If there are no more
packets to send, carrier sense type back-pressure will be active again until switch resources free up. If a collision
occurs, the binary exponential back-off algorithm is skipped and carrier sense is generated immediately, reducing the
chance of further colliding and maintaining carrier sense to prevent reception of packets.
To ensure no packet loss in 10 BASE-T or 100 BASE-TX half duplex modes, the following should be enabled:
1.
Aggressive back off (set Global Register 3 (0x03), bit 0 to ‘1’, or pull high SMAC (pin 69))
2.
No excessive collision drop (set Global Register 4 (0x04), bit 3 to ‘1’, or pull high SMAC (pin 69))
These bits are not set as defaults because the settings are not part of the IEEE standard.
2.4.13 Broadcast Storm Protection
The KS8993F has an intelligent option to protect the switch system from receiving too many broadcast packets.
Broadcast packets will be forwarded to all ports except the source port, and thus use too many switch resources
(bandwidth and available space in transmit queues). The KS8993F has the option to include “multicast packets” for
storm control. The broadcast storm rate parameters are programmed globally, and can be enabled or disabled on a
per port basis. The rate is based on a 67ms interval for 100BT and a 500 ms interval for 10BT. At the beginning of
each interval, the counter is cleared to zero, and the rate limit mechanism starts to count the number of bytes during
the interval. The rate definition is described in Global Registers 6 (0x06) and 7 (0x07). The default setting for registers
6 and 7 is 0x63, which is 99 decimal. This is equal to a rate of 1 %, calculated as follows:
148,800 frames/sec * 67 ms/interval * 1% = 99 frames/interval (approx.) = 0x63h
This means the KS8993F accepts only 1% of broadcast data and filters out 99%.
2.5
MII Interface Operation
相關PDF資料
PDF描述
KSZ8993MLI IC SWITCH 10/100 3PORT 128-PQFP
KSZ8993ML IC SWITCH 10/100 W/TXRX 128PQFP
KSZ8995FQ IC SWITCH 10/100 5PORT 128-PQFP
KSZ8995MA IC SWITCH 10/100 5PORT 128PQFP
KSZ8995MI IC SWITCH 5-PORT 10/100 128PQFP
相關代理商/技術參數
參數描述
KSZ8993FL-EVAL 功能描述:BOARD EVALUATION FOR KSZ8993FL RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
KSZ8993I 功能描述:以太網 IC 3 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-PQFP, I-TEMP RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8993M 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-Ld PQFP (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8993MA5 功能描述:IC SWITCH 10/100 W/TXRX 128PQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝
KSZ8993M-EVAL 功能描述:以太網開發工具 KSZ8993M Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*