Description(Note 1) LED[9][1] Progra" />
參數資料
型號： KS8999
廠商： Micrel Inc
文件頁數： 8/52頁
文件大小： 0K
描述： IC SWITCH 10/100 9PORT 208PQFP
標準包裝： 24
系列： *
類型： *
應用： *
安裝類型： 表面貼裝
封裝/外殼： 208-MQFP，208-PQFP
供應商設備封裝： 208-PQFP（28x28）
包裝： 散裝
配用： 576-1023-ND - BOARD EVAL EXPERIMENT FOR KS8999
KS8999
Micrel
KS8999
16
January 2005
Group
I/O Names
Active Status
Description(Note 1)
LED[9][1]
Programs port duplex (full / half) on port 7. This is only effective if auto-negotiation is
disabled or if this end has auto-negotiation enabled and the far end has auto-
negotiation disabled.
D = Full-duplex, F/U = Half-duplex (default)
LED[9][0]
Programs port duplex (full / half) on port 8. This is only effective if auto-negotiation is
disabled or if this end has auto-negotiation enabled and the far end has auto-
negotiation disabled.
D = Full-duplex, F/U = Half-duplex (default)
LED[6][3]
Programs back-off aggressiveness for half-duplex mode
D = Less aggressive back-off, F/U = More aggressive back-off (default)
LED[6][2]
Programs retries for frames that encounter collisions.
D = Drop frame after 16 collisions, F/U = Continue sending frame regardless of the
number of collisions (default)
LED[6][1:0]
Reserved – use float configuration
LED[7][3]
Programs flow control
D = No flow control, F/U = Flow control enabled (default)
LED[7][2]
Programs broadcast storm protection.
D = 5% broadcast frames allowed, F/U = Unlimited broadcast frames (default)
LED[7][1]
Programs buffer sharing feature.
D = Equal amount of buffers per port (113 buffers), F/U = Share buffers up to 512
buffers on a single port (default)
LED[7][0]
Reserved – use float configuration
LED[8][3]
Programs address aging.
D = Aging disabled, F/U = Enable 5 minute aging (default)
LED[8][2]
Programs frame length enforcement.
D = Max length for VLAN is 1522 bytes and without VLAN is 1518 bytes
F/U = Max length is 1536 bytes (default)
LED[8][1]
Reserved
LED[8][0]
Programs half-duplex back pressure.
D = No half-duplex back pressure, F/U = Half-duplex back pressure enabled (default)
MRXD[3]
Programs port 9 speed
D = 10Mbps, F/U = 100Mbps (default)
MRXD[2]
Programs port 9 duplex
D = Half-duplex, F/U = Full duplex (default)
MRXD[1]
Programs port 9 flow control
D = Flow control, F/U = No flow control (default)
MRXD[0]
D = reserved, F/U = normal operation (default)
CTRL
EN1P
H
Enable 802.1p for all ports – this enables QoS based on the priority field in the layer
2 header.
0 = 802.1p selected by port in EEPROM
1 = Use 802.1p priority field unless disabled in EEPROM
Note: This is also controlled by the EEPROM registers (registers 4-12 bit 4). The values
in the EEPROM supercede this pin. Also, if the priority selection is unaltered in the
EEPROM registers (register 3 bits 0-7) then values above 3 are considered high priorty
and less than 4 are low priority.
MIIS[1:0]
H
MII mode selection – allows the MII to run in the following modes
MIIS
Operating mode
10
0
Disable MII interface
0
1
Reverse MII
1
0
Forward MII
1
7 wire mode (SNI)
Note 1.
All unmanaged programming takes place at reset time only. For unmanaged programming: F = Float, D = Pull-down, U = Pull-up.
See
“Reference Circuits” section.
相關PDF資料
PDF描述
LFXP20E-3FN388I IC FPGA 19.7KLUTS 268I/O 388-BGA
LFXP20C-4FN388C IC FPGA 19.7KLUTS 268I/O 388-BGA
LFXP15E-5F484C IC FPGA 15.4KLUTS 300I/O 484-BGA
LFXP15E-4F484I IC FPGA 15.4KLUTS 300I/O 484-BGA
LFXP15C-5F484C IC FPGA 15.4KLUTS 300I/O 484-BGA
相關代理商/技術參數
參數描述
KS8999_11 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Integrated 9-Port 10/100 Switch with PHY and Frame Buffer
KS8999-EVAL 功能描述:BOARD EVAL EXPERIMENT FOR KS8999 RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板
KS8999I 功能描述:IC SWITCH 9-PORT 10/100 208-PQFP RoHS:否 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝
KS9/KSE9/59/103/115 制造商:PEPPERL+FUCHS 功能描述:Through beam cable sensor,PNP o/p 250mm
KS9~11 制造商:Tohodenzai 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*