參數資料
型號： KS8995XA
廠商： Micrel Inc
文件頁數： 21/51頁
文件大?。?/td> 0K
描述： IC SWITCH 10/100 5PORT 128PQFP
標準包裝： 66
系列： *
類型： *
應用： *
安裝類型： 表面貼裝
封裝/外殼： 128-BFQFP
供應商設備封裝： 128-PQFP（14x20）
包裝： 散裝
配用： 576-1604-ND - EVAL KIT EXPERIMENTAL KS8995XA
KS8995XA
Micrel, Inc.
M9999-051305
28
May 2005
Configuration Interface
The KS8995XA functions as a unmanaged switch. If no EEPROM exists, the KS8995XA will operate from its default and strap-
in settings.
I2C Master Serial Bus Configuration
If a 2-wire EEPROM exists, the KS8995XA can perform more advanced features like broadcast storm protection and rate
control. The EEPROM should have the entire valid configuration data from register 0 to register 109 defined in the memory
map, except the status registers. The configuration access time (t
prgm) is less than 15ms as shown in Figure 10.
....
RST_N
SCL
SDA
t
prgm<15 ms
Figure 10. EEPROM Configuration Timing Diagram
To configure the KS8995XA with a pre-configured EEPROM use the following steps:
At the board level, connect pin 110 on the KS8995XA to the SCL pin on the EEPROM. Connect pin 111 on the
KS8995XA to the SDA pin on the EEPROM.
Be sure the board-level reset signal is connected to the KS8995XA reset signal on pin 115 (RST_N).
Program the contents of the EEPROM before placing it on the board with the desired configuration data. Note that
the first byte in the EEPROM must be “95” for the loading to occur properly. If this value is not correct, all other data
will be ignored.
Place EEPROM on the board and power up the board. Assert the active-low board level reset to RST_N on the
KS8995XA. After the reset is de-asserted, the KS8995XA will begin reading configuration data from the EEPROM.
The configuration access time (t
prgm) is less than 15ms.
Note: For proper operation, make sure pin 47 (PWRDN_N) is not asserted during the reset operation.
MII Management Interface (MIIM)
A standard MIIM interface is provided for all five PHY devices in the KS8995XA. An external device with MDC/MDIO capability
is able to read PHY status or to configure PHY settings. For details on the MIIM interface standard, please reference the IEEE
802.3 specification (section 22.2.4.5). The MIIM interface does not have access to all the configuration registers in the
KS8995XA. It can only access the standard MII registers. See “MIIM Registers” section.
相關PDF資料
PDF描述
KS8997 IC SWITCH 10/100 8PORT 128PQFP
KS8999I IC SWITCH 9-PORT 10/100 208-PQFP
KSZ8001LI TR IC TXRX PHY 10/100 3.3V 48LQFP
KSZ8031RNLI TXRX PHY 10/100 3.3V 24-QFN
KSZ8041MLL TR TXRX 10/100 3.3V PHY MII 48LQFP
相關代理商/技術參數
參數描述
KS8995XA_11 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Integrated 5-Port 10/100 QoS Switch
KS8995XA4 功能描述:IC SWITCH 5-PORT 10/100 128-PQFP RoHS:否 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝
KS8995XAB3 功能描述:IC SWITCH 5-PORT 10/100 128-PQFP RoHS:否 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝
KS8995XA-EVAL 功能描述:EVAL KIT EXPERIMENTAL KS8995XA RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板
KS8995XC 制造商:RF Micro Devices Inc 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*