- 您現在的位置：買賣IC網 > PDF目錄1931 > KS8993FL (Micrel Inc)IC CONV MED 10/100 SGL 128PQFP PDF資料下載
參數資料
| 型號： | KS8993FL |
| 廠商： | Micrel Inc |
| 文件頁數： | 38/99頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CONV MED 10/100 SGL 128PQFP |
| 標準包裝： | 66 |
| 系列： | * |
| 類型： | * |
| 應用： | * |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-BFQFP |
| 供應商設備封裝： | 128-PQFP（14x20） |
| 包裝： | 管件 |
| 配用： | 576-1012-ND - BOARD EVAL EXPERIMENT KS8993F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁
KS8993F
Micrel
August 26, 2004
Revision 1.0
- 43 -
2.10.2 I
2C Slave Serial Bus Configuration
In managed mode, the KS8993F can be configured as an I
2C slave device. In this mode, an I2C master device
(external controller/CPU) has complete programming access to the KS8993F’s 128 registers. Programming access
includes the Global Registers, Port Registers, Media Converter Registers, Advanced Control Registers and indirect
access to the “Static MAC Table”, “VLAN Table”, “Dynamic MAC Table” and “MIB Counters”. The tables and counters
are indirectly accessed via registers 110 thru 120.
In I
2C slave mode, the KS8993F operates like other I2C slave devices. Addressing the KS8993F’s 8 bit registers is
similar to addressing Atmel’s AT24C02 EEPROM’s memory locations. Details of I
2C read/write operations and related
timing information can be found in the AT24C02 Datasheet.
Two fixed 8 bit device addresses are used to address the KS8993F in I
2C slave mode. One is for read; the other is for
write. The addresses are as follow:
1011_1111
<read>
1011_1110
<write>
The following is a sample procedure for programming the KS8993F using the I
2C slave serial bus:
1.
Enable I
2C slave mode by setting the KS8993F strap-in pins PS[1:0] (pins 100 and 101 respectively) to “01”.
2.
Power up the board and assert reset to the KS8993F. After reset, the “Start Switch” bit (register 1 bit 0) will be
set to ‘0’.
3.
Configure the desired register settings in the KS8993F, using the I
2C write operation.
4.
Read back and verify the register settings in the KS8993F, using the I
2C read operation.
5.
Write a ‘1’ to the “Start Switch” bit to start the KS8993F with the programmed settings.
Note: The “Start Switch” bit cannot be set to ‘0’ to stop the switch after an ‘1’ is written to this bit. Thus, it is
recommended that all switch configuration settings are programmed before the “Start Switch” bit is set to ‘1’.
Some of the configuration settings, such as “Aging enable”, “Auto Negotiation Enable”, “Force Speed” and
“Power down” can be programmed after the switch has been started.
2.10.3 SPI Slave Serial Bus Configuration
In managed mode, the KS8993F can be configured as a SPI slave device. In this mode, a SPI master device (external
controller/CPU) has complete programming access to the KS8993F’s 128 registers. Programming access includes
the Global Registers, Port Registers, Media Converter Registers, Advanced Control Registers and indirect access to
the “Static MAC Table”, “VLAN Table”, “Dynamic MAC Table” and “MIB Counters”. The tables and counters are
indirectly accessed via registers 110 thru 120.
The KS8993F supports two standard SPI commands: ‘0000_0011’ for data read and ‘0000_0010’ for data write. SPI
multiple read and multiple write are also supported by the KS8993F to expedite register read back and register
configuration, respectively.
SPI multiple read is initiated when the master device continues to drive the KS8993F SPIS_N input pin (SPI Slave
Select signal) low after a byte (a register) is read. The KS8993F internal address counter will increment automatically
to the next byte (next register) after the read. The next byte at the next register address will be shifted out onto the
KS8993F SPIQ output pin. SPI multiple read will continue until the SPI master device terminates it by de-asserting the
SPIS_N signal to the KS8993F.
相關PDF資料 |
PDF描述 |
|---|---|
| KS8993I | IC SWITCH 10/100 3PORT 128PQFP |
| KS8993ML | IC SWITCH 10/100 3PORT 128PQFP |
| KS8995MAI | IC SWITCH 10/100 5PORT 128PQFP |
| KS8995MI | IC SWITCH 10/100 5PORT 128PQFP |
| KS8995XA | IC SWITCH 10/100 5PORT 128PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KS8993FL-EVAL | 功能描述:BOARD EVAL EXPERIMENT KS8993F RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板 |
| KS8993I | 功能描述:IC SWITCH 10/100 3PORT 128PQFP RoHS:否 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
| KS8993M | 功能描述:IC SWITCH 10/100 3PORT 128PQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
| KS8993M_11 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Integrated 3-Port 10/100 Managed Switch with PHYs |
| KS8993MA5 | 功能描述:IC SWITCH 3-PORT 10/100 128-PQFP RoHS:否 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
發布緊急采購，3分鐘左右您將得到回復。