參數資料
型號： KMPC885ZP133
廠商： Freescale Semiconductor
文件頁數： 6/87頁
文件大小： 0K
描述： IC MPU POWERQUICC 133MHZ 357PBGA
標準包裝： 2
系列： MPC8xx
處理器類型： 32-位 MPC8xx PowerQUICC
速度： 133MHz
電壓： 3.3V
安裝類型： 表面貼裝
封裝/外殼： 357-BBGA
供應商設備封裝： 357-PBGA（25x25）
包裝： 托盤
MPC885/MPC880 PowerQUICC Hardware Specifications, Rev. 7
14
Freescale Semiconductor
Thermal Calculation and Measurement
If the board temperature is known, an estimate of the junction temperature in the environment can be made
using the following equation:
TJ = TB + (RθJB × PD)
where:
RθJB = junction-to-board thermal resistance (C/W)
TB = board temperature (C)
PD = power dissipation in package
If the board temperature is known and the heat loss from the package case to the air can be ignored,
acceptable predictions of junction temperature can be made. For this method to work, the board and board
mounting must be similar to the test board used to determine the junction-to-board thermal resistance,
namely a 2s2p (board with a power and a ground plane) and vias attaching the thermal balls to the ground
plane.
7.4
Estimation Using Simulation
When the board temperature is not known, a thermal simulation of the application is needed. The simple
two resistor model can be used with the thermal simulation of the application [2], or a more accurate and
complex model of the package can be used in the thermal simulation.
7.5
Experimental Determination
To determine the junction temperature of the device in the application after prototypes are available, the
thermal characterization parameter (
ΨJT) can be used to determine the junction temperature with a
measurement of the temperature at the top center of the package case using the following equation:
TJ = TT + (ΨJT × PD)
where:
Ψ
JT = thermal characterization parameter
TT = thermocouple temperature on top of package
PD = power dissipation in package
The thermal characterization parameter is measured per the JESD51-2 specification published by JEDEC
using a 40 gauge type T thermocouple epoxied to the top center of the package case. The thermocouple
should be positioned so that the thermocouple junction rests on the package. A small amount of epoxy is
placed over the thermocouple junction and over about 1 mm of wire extending from the junction. The
thermocouple wire is placed flat against the package case to avoid measurement errors caused by the
cooling effects of the thermocouple wire.
相關PDF資料
PDF描述
IDT70V3389S5BF IC SRAM 1.125MBIT 5NS 208FBGA
ASM43DREI CONN EDGECARD 86POS .156 EYELET
KMPC885VR80 IC MPU POWERQUICC 80MHZ 357PBGA
KMPC885VR66 IC MPU POWERQUICC 66MHZ 357PBGA
KMPC885VR133 IC MPU POWERQUICC 133MHZ 357PBGA
相關代理商/技術參數
參數描述
KMPC885ZP66 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Hardware Specifications
KMPC885ZP80 功能描述:微處理器 - MPU PQ I HIP6W DUET RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
KMPG666-4 制造商:Kingstate Electronics Corporation 功能描述:
KMQ100VB102M18X35LL 功能描述:鋁質電解電容器 - 帶引線 1000UF 100V RoHS:否 制造商:Kemet 引線類型: 電容:220 uF 容差:20 % 電壓額定值:25 V 工作溫度范圍: 端接類型:Radial 外殼直徑:8 mm 外殼長度:11 mm 引線間隔:5 mm 產品:General Purpose Electrolytic Capacitors 封裝:Bulk
KMQ160VS102M22X40T2 功能描述:CAP ALUM 1000UF 160V 20% SNAP RoHS:否 類別:電容器 >> 鋁 系列:KMQ 標準包裝:2,000 系列:142 RHS 電容:4700µF 額定電壓:10V 容差:±20% 壽命@溫度:105°C 時為 2000 小時 工作溫度:-40°C ~ 105°C 特點:通用 紋波電流:1.26A ESR（等效串聯電阻）:- 阻抗:- 安裝類型:通孔 封裝/外殼:徑向，Can 尺寸/尺寸:0.492" 直徑（12.50mm） 高度 - 座高（最大）:1.063"（27.00mm） 引線間隔:0.197"（5.00mm） 表面貼裝占地面積:- 包裝:散裝
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*