- 您現在的位置：買賣IC網 > PDF目錄17116 > KITMPR083EVM (Freescale Semiconductor)KIT EVAL 8POSITION ROTARY TOUCH PDF資料下載
參數資料
| 型號： | KITMPR083EVM |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 34/35頁 |
| 文件大小： | 0K |
| 描述： | KIT EVAL 8POSITION ROTARY TOUCH |
| 標準包裝： | 1 |
| 傳感器類型： | 觸摸，電容式 |
| 傳感范圍： | 8 個按鈕/鍵 |
| 接口： | I²C |
| 電源電壓： | 1.8 V ~ 3.6 V |
| 嵌入式： | 是，其它 |
| 已供物品： | 板，纜線，CD |
| 已用 IC / 零件： | MPR083 |
| 相關產品： | MPR083EJR2CT-ND - IC CTLR TOUCH SENSR PROX 16TSSOP MPR083QR2-ND - IC CTLR TOUCH SENSOR PROX 16-QFN MPR083Q-ND - IC CTLR TOUCH SENSOR PROX 16-QFN MPR083EJR2TR-ND - IC CTLR TOUCH SENSR PROX 16TSSOP MPR083EJ-ND - IC CTLR TOUCH SENSR PROX 16TSSOP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁
MPR083
Sensors
8
Freescale Semiconductor
When performing read-after-write verification, remember to re-set the command byte’s address because the stored command
byte address will generally have been auto-incremented after the write (Section 2.4).
Figure 12. ‘n’ Data Bytes Received
2.3.8
Operation with Multiple Master
The application should use repeated starts to address the MPR083 to avoid bus confusion between I2C masters.On a I2C bus,
once a master issues a start/repeated start condition, that master owns the bus until a stop condition occurs. If a master that does
not own the bus attempts to take control of that bus, then improper addressing may occur. An address may always be rewritten
to fix this problem. Follow I2C protocol for multiple master configurations.
2.3.9
Device Reset
The RST is an active-low software reset. This is implemented in the Configuration Register by activating the RST bit. When
asserted, the device clears any transaction to or from the MPR083 on the serial interface and configures the internal registers to
the same state as a power-up reset (Table 4). The MPR083 then waits for a START condition on the serial interface.
The sensor controller is capable of operating down to 1.8 V, however, in order for the sensor controller to exit reset and startup
correctly the host system must initially provide 2.0 V to 3.6 V input to VDD and then follow the process in Figure 13. This process
is required in applications that require regulated operation in the 1.8 V to 2.0 V range. In the case that the application uses an
unregulated battery, then the battery must initially provide at least 2.0 V to correctly power-up the sensor controller which limits
battery selection to the 2.0 V to 3.6 V range.
Figure 13. Low Voltage (1.8 V - 2.0 V) Power-up Sequence
SAAA P
1
SLAVE ADDRESS
COMMAND BYTE
DATA BYTE
acknowledge from MPR083
R/W
nbytes
auto-increment memory
word address
D15 D14 D13 D12 D11 D10 D9 D8
D1 D0
D3 D2
D5 D4
D7 D6
Howcommand byte and data byte
map into MPR083's registers
acknowledge from
MPR083
acknowledge from
MPR083
Established Comms with
Sensor Controller?
i.e. Read from FIFO
Is Data valid? (0 x 40)
Idle Delay Loop
Apply 2.0V to VDD Max
To Sensor Controller
Lower VDD to the desired operating voltage
1.8 V to 2.0 V
False
True
相關PDF資料 |
PDF描述 |
|---|---|
| RCC12DREN-S734 | CONN EDGECARD 24POS .100 EYELET |
| VE-J7P-EZ | CONVERTER MOD DC/DC 13.8V 25W |
| GBM28DSEN | CONN EDGECARD 56POS .156 EYELET |
| ADR06WARZ-RL | IC VREF SERIES PREC 3V 8SOIC |
| RCC12DREH-S734 | CONN EDGECARD 24POS .100 EYELET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KITMPR084EVM | 功能描述:光學傳感器開發工具 8 TOUCH PADS RoHS:否 制造商:ams 工具用于評估: 接口類型: 最大工作溫度: |
| KITMPR121EVM | 功能描述:觸摸傳感器開發工具 MPR121 Sensor Tool Box RoHS:否 制造商:Cypress Semiconductor 工具用于評估: 接口類型: 工作電壓: 最大工作溫度: |
| KITMPR121EVM | 制造商:Freescale Semiconductor 功能描述:Sensor Toolbox Proximity Sensor Kit |
| KITMPVZ5004EVK | 功能描述:壓力傳感器開發工具 WATER LEVEL BOARD RoHS:否 制造商:Freescale Semiconductor 工具用于評估:MPL3115A2 接口類型:USB 最大工作溫度: |
| KITMPXA6115AEVB | 功能描述:壓力傳感器開發工具 Sensor Toolbx Pressu Sensor Developmt brd RoHS:否 制造商:Freescale Semiconductor 工具用于評估:MPL3115A2 接口類型:USB 最大工作溫度: |
發布緊急采購，3分鐘左右您將得到回復。