- 您現在的位置：買賣IC網 > PDF目錄374311 > KB2511B (SAMSUNG SEMICONDUCTOR CO. LTD.) ACB 14C 14#16 PIN RECP BOX PDF資料下載
參數資料
| 型號： | KB2511B |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | ACB 14C 14#16 PIN RECP BOX |
| 中文描述： | 偏轉處理器多同步監測儀 |
| 文件頁數： | 23/35頁 |
| 文件大?。?/td> | 337K |
| 代理商： | KB2511B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
KB2511B DEFLECTION PROCESSOR FOR MULTISYNC MONITORS
22
[ ] initlal value
OPERATING DESCRIPTION
GENERAL CONSIDERATIONS
Power Supply
The typical values of the power supply voltages Vcc and V
DD
are respectively 12V and 5V. Perfect operation is
obtained if Vcc and V
DD
are maintened in the limits: 10.8 to 13.2V and 4.5 to 5.5V.
In order to avoid erratic operation of the circuit during transient phase of Vcc switching on, or switching off, the
value of Vcc is monitored and the outputs of the circuit are inhibited if Vcc is less than 7.5V typically.
In the same manner, V
DD
is monitored and internal set-up is made until V
DD
reaches 4V (see I
2
C control table for
power on reset).
In order to have a very good power supply rejection, the circuit is internally powered by several internal voltage
references (the unigue typical value of which is 8V). Two of these voltage references are externally accessible, one
for the vertical part and on one for the horizontal one. If needed, these voltage references can be used (until Iload
is less than 5mA). Furthermore it is necessary to filter the a.m. voltage references by the use of external capacitor
connected to ground, in order to minimize the noise and consequently the
“
jitter
”
on vertical and horizontal output
signals.
I
2
C Control
KB2511 belongs to the I
2
C controlled device family, instead of being controlled by DC voltage on dedicated control
pins, each adjustment can be realized through the I
2
C interface. The I
2
C bus is a serial bus with a clock and a data
input. The general function and the bus protocol are specified in the philips-bus data sheets.
The interface (data and clock) is TTL-level compatible. The internal threshold level of the input comparator is 2.2V
(when V
DD
is 5V). Spikes of up to 500ns are filtered by an integrator and maximum clock speed is limited to
400kHz.
The data line (SDA) can be used in a bidirectional way that means in read-mode the IC clocks out a reply informa-
tion (1byte) to the micro-processor.
The bus protocol prescribes always a full-byte transmission. The first byte after the start condition is used to trans-
mit the IC-address (hexa 8C for write, 8D for read).
Write Mode
In write mode the second byte sent contains the subaddress of the selected function to adjust (or controls to affect)
and the third byte the corresponding data byte. It is possible to send more than one data byte to the IC. If after the
third byte no stop or start condition is detected, the circuit increments automatically the momentary subaddress in
the subaddress counter by one (auto-increment mode). So it is possible to transmit immediately the next data
bytes without sending the IC address or subaddress. It can be useful so as to reinitialize the whole controls very
quickly (flash manner). This procedure can be finished by a stop condition.
The circuit has 16 adjustment capabilities: 3 for horizontal part, 4 for vertical one, 2 for E/W correction, 2 for the
dynamic horizontal phase control, 1 for moire option, 3 for horizontal and vertical dynamic focus and 1 for B+
reference adjustment.
17 bits are also dedicated to several controls (ON/OFF, horizontal forced frequency, sync priority, detection
refresh and Xray reset).
READ MODE
00
Hlock
0, on
[1], no
Vlock
0, on
[1], no
Xray
1,on
[0],off
Polarity detection
Synchro detection
H/V pol
[1],negative
V pol
[1], negative
Vext det
[0],no det
H/V det
[0],no det
V det
[0], nodet
相關PDF資料 |
PDF描述 |
|---|---|
| KB2512 | DEFLECTION PROCESSOR FOR MULTISYNC MONITORS |
| KB2514 | VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS |
| KB2516 | TRIPLE 8-BIT ANALOG-TO-DIGITAL CONVERTER |
| KB9223 | RF AMP & SERVO SIGNAL PROCESSOR |
| KB9223-L | RF AMP & SERVO SIGNAL PROCESSOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KB2512 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:DEFLECTION PROCESSOR FOR MULTISYNC MONITORS |
| KB2514 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:VIDEO AMP MERGED OSD PROCESSOR FOR MONITORS |
| KB2516 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:TRIPLE 8-BIT ANALOG-TO-DIGITAL CONVERTER |
| KB2531S28 | 功能描述:POT 25K OHM 2W REV LOG TAPER RoHS:是 類別:電位計，可變電阻器 >> 旋轉 - 對數 系列:K 標準包裝:25 系列:51 電阻（歐姆）:10k 功率（瓦特）:0.25W，1/4W 容差:±20% 溫度系數:±1000ppm/°C 匝數:單路 旋轉:290° 調節型:側面調節 電阻材料:導電塑料 端接類型:PCB 引腳 觸動器長度:0.875"（22.22mm） 觸動器類型:開槽軸 觸動器直徑:0.125"（3.18mm） 尺寸 - 主體:方形 - 0.350" L x 0.492" W x 0.522" H（8.89mm x 12.50mm x 13.25mm） 安裝類型:通孔 包裝:散裝 |
| KB2541S28 | 功能描述:POT 250K OHM 2W REV LOG TAPER RoHS:是 類別:電位計，可變電阻器 >> 旋轉 - 對數 系列:K 標準包裝:25 系列:51 電阻（歐姆）:10k 功率（瓦特）:0.25W，1/4W 容差:±20% 溫度系數:±1000ppm/°C 匝數:單路 旋轉:290° 調節型:側面調節 電阻材料:導電塑料 端接類型:PCB 引腳 觸動器長度:0.875"（22.22mm） 觸動器類型:開槽軸 觸動器直徑:0.125"（3.18mm） 尺寸 - 主體:方形 - 0.350" L x 0.492" W x 0.522" H（8.89mm x 12.50mm x 13.25mm） 安裝類型:通孔 包裝:散裝 |
發布緊急采購，3分鐘左右您將得到回復。