- 您現在的位置：買賣IC網 > PDF目錄9972 > KAD5612P-12Q72 (Intersil)IC ADC 12BIT 125MSPS DUAL 72-QFN PDF資料下載
參數資料
| 型號： | KAD5612P-12Q72 |
| 廠商： | Intersil |
| 文件頁數： | 7/29頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT 125MSPS DUAL 72-QFN |
| 產品培訓模塊： | High-Speed Analog-to-Digital Converters |
| 標準包裝： | 1 |
| 系列： | FemtoCharge™ |
| 位數： | 12 |
| 采樣率（每秒）： | 125M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 369mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 72-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 72-QFN（10x10） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 2 個差分，單極 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
15
FN6803.2
September 9, 2009
The calibration sequence is initiated on the rising edge of
RESETN, as shown in Figure 23. The over-range output
(OR) is set high once RESETN is pulled low, and remains in
that state until calibration is complete. The OR output returns
to normal operation at that time, so it is important that the
analog input be within the converter’s full-scale range to
observe the transition. If the input is in an over-range
condition the OR pin will stay high, and it will not be possible
to detect the end of the calibration cycle.
While RESETN is low, the output clock
(CLKOUTP/CLKOUTN) is set low. Normal operation of the
output clock resumes at the next input clock edge
(CLKP/CLKN) after RESETN is deasserted. At 250MSPS
the nominal calibration time is 200ms, while the maximum
calibration time is 550ms.
User-Initiated Reset
Recalibration of the ADC can be initiated at any time by
driving the RESETN pin low for a minimum of one clock
cycle. An open-drain driver with a drive strength of less than
0.5mA is recommended, RESETN has an internal high
impedance pull-up to OVDD. As is the case during power-on
reset, the SDO, RESETN and DNC pins must be in the
proper state for the calibration to successfully execute.
The performance of the KAD5612P changes with variations
in temperature, supply voltage or sample rate. The extent of
these changes may necessitate recalibration, depending on
system performance requirements. Best performance will be
achieved by recalibrating the ADC under the environmental
conditions at which it will operate.
A supply voltage variation of less than 100mV will generally
result in an SNR change of less than 0.5dBFS and SFDR
change of less than 3dBc.
In situations where the sample rate is not constant, best
results will be obtained if the device is calibrated at the
highest sample rate. Reducing the sample rate by less than
75MSPS will typically result in an SNR change of less than
0.5dBFS and an SFDR change of less than 3dBc.
and SFDR performance with calibration performed at -40°C,
+25°C, and +85°C. Each plot shows the variation of
SNR/SFDR across temperature after a single calibration at
-40°C, +25°C and +85°C. Best performance is typically
achieved by a user-initiated calibration at the operating
conditions, as stated earlier. However, it can be seen that
performance drift with temperature is not a very strong
function of the temperature at which the calibration is
performed. Full-rated performance will be achieved after
power-up calibration regardless of the operating conditions.
Analog Input
Each ADC core contains a fully differential input
(AINP/AINN, BINP/BINN) to the sample and hold amplifier
(SHA). The ideal full-scale input voltage is 1.45V, centered at
the VCM voltage of 0.535V as shown in Figure 26.
Best performance is obtained when the analog inputs are
driven differentially. The common-mode output voltage,
VCM, should be used to properly bias the inputs as shown in
FIGURE 23. CALIBRATION TIMING
CLKP
CLKN
CLKOUTP
RESETN
ORP
CALIBRATION
BEGINS
CALIBRATION
COMPLETE
CALIBRATION
TIME
-4
-3
-2
-1
0
1
2
3
-40
-15
10
35
60
85
SNR
C
HANGE
(d
B
fs)
CAL DONE AT
+85°C
TEMPERATURE (°C)
CAL DONE AT
-40°C
CAL DONE AT
+25°C
FIGURE 24. SNR PERFORMANCE vs TEMPERATURE
FIGURE 25. SFDR PERFORMANCE vs TEMPERATURE
-15
-10
-5
0
5
10
15
-40
-15
10
35
60
85
SFDR
CHANGE
(dBc)
TEMPERATURE (°C)
CAL DONE AT
-40°C
CAL DONE AT
+25°C
CAL DONE AT
+85°C
KAD5612P
相關PDF資料 |
PDF描述 |
|---|---|
| V48B2M100BF2 | CONVERTER MOD DC/DC 2V 100W |
| MS27484E18B11P | CONN PLUG 11POS STRAIGHT W/PINS |
| V48B2M100BF | CONVERTER MOD DC/DC 2V 100W |
| MS27473P22A55S | CONN PLUG 55POS STRAIGHT W/SCKT |
| V48B2M100BL3 | CONVERTER MOD DC/DC 2V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KAD5612P-17Q72 | 功能描述:IC ADC 12BIT 170MSPS DUAL 72-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:FemtoCharge™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:250 系列:- 位數:12 采樣率（每秒）:1.8M 數據接口:并聯 轉換器數目:1 功率耗散（最大）:1.82W 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-LQFP 供應商設備封裝:48-LQFP（7x7） 包裝:管件 輸入數目和類型:2 個單端，單極 |
| KAD5612P-21Q72 | 制造商:Intersil Corporation 功能描述:ADC DUAL PIPELINED 210MSPS 12-BIT PARALLEL 72QFN EP - Rail/Tube 制造商:Intersil Corporation 功能描述:IC ADC 12BIT 210MSPS DUAL 72-QFN 制造商:Intersil Corporation 功能描述:12-Bit, 210MSPS Dual-Channel ADC, Programmable LVDS/LVCMOS Outputs. 72- QFN 制造商:Intersil Corporation 功能描述:KAD5612P Series Dual Ch 12-Bit SMT Analog to Digital Converter QFN-72EP 制造商:Intersil Corporation 功能描述:Analog to Digital Converters - ADC 12-BIT 210MSPS DL-CH ADC PROG LVDS/LVCMOS |
| KAD5612P-25Q72 | 制造商:Intersil Corporation 功能描述:ADC DUAL PIPELINED 250MSPS 12-BIT PARALLEL 72QFN EP - Rail/Tube 制造商:Intersil Corporation 功能描述:IC ADC 12BIT 250MSPS DUAL 72-QFN 制造商:Intersil Corporation 功能描述:IC, ADC, 12BIT, Resolution (Bits):12bit, Sampling Rate:250MSPS, Supply Voltage T |
| KA-D9E-011 | 制造商:Leach International Corporation 功能描述:MID RANGE - Bulk |
| KA-D9F-005 | 制造商:Leach International Corporation 功能描述:MID RANGE - Bulk |
發布緊急采購，3分鐘左右您將得到回復。