- 您現在的位置：買賣IC網 > PDF目錄383182 > ISL9440A (Intersil Corporation) Triple, 180∑ Out-of-Phase, Step-Down PWM and Single Linear Controller PDF資料下載
參數資料
| 型號： | ISL9440A |
| 廠商： | Intersil Corporation |
| 英文描述： | Triple, 180∑ Out-of-Phase, Step-Down PWM and Single Linear Controller |
| 中文描述： | 三，180Σ門診的階段，降壓型PWM和線性控制器單 |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 978K |
| 代理商： | ISL9440A |
9
FN6383.1
December 5, 2007
Pin Descriptions
BOOT3, BOOT2, BOOT1 (Pin 20, 26, 31)
These pins are bootstrap pins to provide bias for high side
driver. The bootstrap diodes are integrated to help reduce
total cost and reduce layout complexity.
UGATE3, UGATE2, UGATE1 (Pin 21, 27, 30)
These pins provide the gate drive for the upper MOSFETs.
PHASE3, PHASE2, PHASE1 (Pin 19, 25, 32)
These pins are connected to the junction of the upper
MOSFET’s source, output filter inductor, and lower MOSFET’s
drain.
LGATE3, LGATE2, LGATE1 (Pin 22, 28, 29)
These pins provide the gate drive for the lower MOSFETs.
PGND (Pin 23)
This pin provides the power ground connection for the lower
gate drivers for all PWM1, PWM2 and PWM3. This pin
should be connected to the sources of the lower MOSFETs
and the (-) terminals of the external input capacitors.
FB3, FB2, FB1, LDOFB (Pin 16, 13, 6, 10)
These pins are connected to the feedback resistor divider
and provide the voltage feedback signals for the respective
controller. They set the output voltage of the converter. In
addition, the PGOOD circuit uses these inputs to monitor the
output voltage status.
ISEN3, ISEN2, ISEN1 (Pin 18, 24, 1)
These pins are used to monitor the voltage drop across the
lower MOSFET for current loop feedback and overcurrent
protection.
PGOOD (Pin 2)
This is an open drain logic output used to indicate the status
of the output voltages AND input voltage (voltage on VIN pin;
early warning for ISL9440 and ISL9440A). This pin is pulled
low when either of the three PWM outputs is not within 10%
of the respective nominal voltage, or if the linear controller
output is less than 75% of it’s nominal value, or VIN pin
voltage drops below 5.55V.
ISL9440 and ISL9440A’s PGOOD pin also indicates the VIN
pin status for early warning function. If the voltage on VIN pin
drops below 5.55V, this pin will be pulled low.
SGND (Pin 11)
This is the small-signal ground, common to all 4 controllers,
and are suggested to be routed separately from the high
current ground (PGND). In case of one whole solid ground
and no noisy current going through around chip, SGND and
PGND can be tied to the same ground copper plane. All
voltage levels are measured with respect to this pin. A small
ceramic capacitor should be connected right next to this pin
for noise decoupling.
VIN (Pin 4)
Use this pin to power the device with an external supply
voltage with a range of 5.6V to 24V. For 5V ±10% operation,
connect this pin to VCC_5V.
For ISL9440 and ISL9440A, the voltage on this pin is
monitored for early warning function. If the voltage on this
pin drop below 5.55V, the PGOOD will be pulled low. RST
will be low after PGOOD toggles to low for 5.5μs (TYP).
Refer to Figure 1 for detailed time sequence.
ISL9441 doesn’t have early warning functions, which means
the VIN pin voltage is not monitored.
VCC_5V (Pin 3)
This pin is the output of the internal 5V linear regulator. This
output supplies the bias for the IC, the low side gate drivers,
and the external boot circuitry for the high side gate drivers.
The IC may be powered directly from a single 5V (±10%)
supply at this pin. When used as a 5V supply input, this pin
must be externally connected to V
IN
. The VCC_5V pin must
be always decoupled to power ground with a minimum of
4.7
μ
F ceramic capacitor, placed very close to the pin.
EN3, EN2, EN1 (Pin 17, 14, 5)
These pins provide an enable/disable function for their
respective PWM output. The output is enabled when this pin
is floating or pulled HIGH, and disabled when the pin is
pulled LOW.
G4 (Pin 9)
This pin is the open drain output of the linear regulator
controller.
OCSET3, OCSET2, OCSET1 (Pin 15, 12, 7)
A resistor from this pin to ground sets the overcurrent
threshold for the respective PWM.
RST (Pin 8)
Reset pulse output. This pin outputs a logic LOW signal after
PGOOD toggles to low for 5.5μs (TYP). It can be used to
reset system.
Refer to Figure 1 for detailed time sequence of ISL9440 and
ISL9440A with early warning function.
ISL9441 doesn’t have early warning functions, which means
the VIN pin voltage is not monitored. But RST still output
LOW signal following PGOOD LOW.
ISL9440, ISL9440A, ISL9441
相關PDF資料 |
PDF描述 |
|---|---|
| ISL9441 | Triple, 180∑ Out-of-Phase, Step-Down PWM and Single Linear Controller |
| ISL95810UIRT8 | Low Noise, Low Power I2C Bus, 256 Taps |
| ISL95810UIU8Z | Single Digitally Controlled Potentiometer (XDCP) |
| ISL95810 | Single Digitally Controlled Potentiometer (XDCP) |
| ISL95810WIU8Z | Single Digitally Controlled Potentiometer (XDCP) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL9440AEVAL1Z | 功能描述:EVALUATION BOARD FOR ISL9440 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL9440AIRZ | 功能描述:IC REG QD BCK/LINEAR SYNC 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓撲:降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| ISL9440AIRZ-T | 功能描述:IC REG QD BCK/LINEAR SYNC 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓撲:降壓（降壓）同步（2），線性（LDO）（1） 功能:任何功能 輸出數:3 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:4.5 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:28-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:* 包裝:帶卷 (TR) 其它名稱:ISL6402IVZ-TTR |
| ISL9440BEVAL1Z | 功能描述:EVAL BOARD 1 FOR ISL9440B RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL9440BIRZ | 功能描述:IC REG QD BCK/LINEAR SYNC 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓撲:降壓（降壓）同步（2），線性（LDO）（1） 功能:任何功能 輸出數:3 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:4.5 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:28-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:* 包裝:帶卷 (TR) 其它名稱:ISL6402IVZ-TTR |
發布緊急采購，3分鐘左右您將得到回復。